Quick HECTOR HC 712 Manuel De L'utilisateur page 15

POS. DESCRIPTION
23 Pressure lever
24 Spring for pressure lever
25 Screw for pressure lever
26 Plug
27 Spring
28 Gypsy lock lever
29 Rope/chain stripper
30 Screw
31 Lock lever control
32 Spring
33 Screw
34 Washer
35 Nut
36 Studs
37 Washer
38 Grower
39 Nut
40 Screw
41A "HC" casing in plastic
41B "HC" casing in aluminium
42 Casing gasket
43 Circlip
44 Internal circlip
45 Bearing 7205
46 Worm screw
47 Bearing 6204
48 Oil cap
49 Oil cap seal
50 O-ring
51 "HC" cable outlet
52A Electric motor 700W 12V
52B Electric motor 700W 24V
52C Electric motor 1000W 12V
52D Electric motor 1000W 24V
52E Electric motor 1500W 12V
52F Electric motor 1500W 24V
53 Key
54 Sensor
55 Red "HC" motor cable
56 Black "HC" motor cable
57 "HC" controlcable
58 "HC" copper bracket right
59 "HC" copper bracket left
60A Reversing contactor unit
T6415-12 12V
60B Reversing contactor unit
T6415-24 24V
61 Screw
HECTOR 700/1000/1500W - REV007A
CODE
PDLVTDHC0000
MMTND07G0000
MSMVT07G0000
Quick
MBSC12036A00
to marine environments. In any case, any salt deposits on the
MMBLBRATC000
MSH10HCX0000
outside must be removed periodically to avoid corrosion and
MSN10HCXR100
damage to the equipment.
MBV0616MXCE0
The parts where salt may have built up should be washed thor-
PVLBBHC00000
oughly with fresh water.
MM108077X000
MBV0645MXCE0
Once a year, the drum and the gypsy are to be taken apart as
MBR06X000000
follows:
MBD06MXET000
MPB100800X00
GYPSY SIDE
MBR10X000000
Using the handle (22) remove the bush (2) loosen the screws
MBG10X000000
(21), remove the gypsy cover (20) and the top clutch cone (19);
MBD10MXEN000
loosen the fi xing screws (30) of the rope/chain stripper (29)
MBV0516MXCE0
PDCHC2150000
and remove it (leave the pin, spring and handle in place).
SGMCRHC21500
Pull off the gypsy (18).
PGCRHC000000
PGPRL2552100
DRUM SIDE
MBAN5220Y000
With the handle (22) release the bush (2) and pull off the drum
MBJ7205BE000
(3).
MSLVT10HC000
MBJ620400000
Clean all the parts removed to avoid corrosion and grease
MNTP38T00000
(with marine grease) the shaft thread (14, 15 or 16) and the
MMGUTPLHC000
gypsy (18) where the clutch cones rest (17 and 19).
PGR031180000
PPSPHC000000
EMF071200000
EMF072400000
EMF101200000
EMF102400000
EMF151200000
EMF152400000
MBH050515F00
KNREEDCL0000
SAECC135HCR0
SAECC135HCB0
ECC100400L00
ECBRAHCLDR01
ECBRAHCLSR01
ERT641524000
ERT641512000
MBV0525MXCE0
MAINTENANCE
WARNING: make sure the electrical power to the motor
is switched off when working manually on the windlass.
Carefully remove the chain or rope from the gypsy or the
rope from the drum.
® windlasses are manufactured with materials resistant
GB
15