Monitor Ringtone Selection Procedure - Comelit MT KIT 13 Manuel Technique

GROUP S.P.A.
On secondary monitors, Pushbutton 2 also has the video request
function (for more information see page 37).
Switchboard call ➔ Press the pushbutton set in this mode to send
a call to the system porter Switchboard.
Single-residence intercom call ➔ Press the pushbutton set in this
mode to send a call to the other units (video door-entry phones
and/or door-entry phones) set to the same call address.
By lifting the handset, the receiver of the call communicates with
the caller.
The communication is ended by hanging up the handset.
In any case, a call from the external unit always has priority over an
intercom call. In this situation, users who are already speaking will
hear a tone similar to the ringtone in the handset if the latter is for
them, otherwise a triple signal tone will sound.
To answer the call from the external unit, simply lift the handset of
any free unit or hang up and lift the handset of a unit engaged in
the intercom call.
Activation of communication with the external unit interrupts the
intercom conversation previously in progress.
An intercom call does not have priority over a conversation/call with
the external unit.
In this case, during an intercom call attempt, the LED will flash for a
few seconds to signal that the system is engaged.
Two-residence intercom call ➔ Press the pushbutton set in this
mode to send a call to the other units (video door-entry phones
and/or door-entry phones) set to the two-residence call address, as
indicated in the table on page 33.
By lifting the handset, the receiver of the call communicates with
the caller. The communication is ended by hanging up the handset.
In any case, a call from the external unit always has priority over an
intercom call.
In this situation, users who are already speaking will hear a tone
similar to the ringtone in the handset if the latter is for them, otherwise
a triple signal tone will sound.
To answer the call from the external unit, simply lift the handset of
any free unit or hang up and lift the handset of a unit engaged in
the intercom call.
Activation of communication with the external unit interrupts the
intercom conversation previously in progress.
An intercom call does not have priority over a conversation/call with
the external unit.
In this case, during an intercom call attempt, the LED will flash for a
few seconds to signal that the system is engaged.
Doctor function management ➔ The Doctor function enables
automatic activation of the door lock release device with a call to
the address of the video door-entry phone and/or door-entry phone
where the function was activated, by the external unit.
With the function activated, the signalling LED stays on. The Doctor
function is enabled or disabled by pressing the pushbutton set for
that function for 2 seconds.
Privacy Service management ➔ The Privacy function enables the
exclusion of calls from the external unit or switchboard.
NOTE The Doctor and Privacy functions may NOT be activated at
the same time.
36
MT KIT 13

Monitor ringtone selection procedure

The user can select the monitor ringtone from a list of available
ringtones, carrying out the following procedure:
1 Keep the pushbutton pressed until a confirmation tone
sounds (this operation is only possible with the system in
standby mode; otherwise the signalling LED will flash to warn
the user).
2 Press and release the
once (a confirmation tone sounds) to change the call ringtone
from the external unit.
twice (2 confirmation tones sound) to change the switchboard
call tone.
three times (3 confirmation tones sound) to change the door
bell ringtone.
Any further pressing of the
sequence described above.
After the last time the
confirmation tone before proceeding to the next stage.
3 Press and release the
various available ringtones in sequence. If you want to hear the
same ringtone several times, keep the
pressed.
4 Press the key to confirm selection of the last ringtone heard
and to exit (at any time) the monitor ringtone selection mode.
On exiting monitor ringtone selection mode a confirmation tone
will sound.
pushbutton:
pushbutton repeats the
pushbutton is pressed, wait for a
pushbutton to scroll through the
pushbutton