Husqvarna ROYAL 49S Mode D'emploi page 12

IMPORTANT
Do not attempt any maintenance on your lawnmower
when the engine is hot.
Cleaning
IMPORTANT
Never use water for cleaning your lawnmower. Do not
clean with chemical, including petrol, or solvents - some
can destroy critical plastic parts.
1. Remove grass from under the deck with a brush (N1
and N2).
N1
2. Using a soft brush -
remove grass clippings
from the engine air
intakes and exhaust (N3),
cutting height adjustment
area. (N4), around the
wheels (N5) and the
grassbox (N6 & N7).
3. Wipe over the surface of your lawnmower with a dry cloth.
N4
N6
Cutting System
Removing the Blade
P1 or P2 BBC Only
• Disconnect the spark
plug lead.
1. Use spanner to loosen
blade bolt by turning
anti-clockwise.
2. Remove the blade bolt,
blade and spacer washer.
3. Inspect for damage and
clean as necessary.
Fitting the Blade
P1 or P2 BBC Only
1. Fit the blade to the
machine with the sharp
edges pointing away from the machine.
2. Re-assemble blade bolt through blade and spacer
washer.
3. Hold firmly and tighten blade bolt firmly with a
spanner. Do not over tighten.
English - 7
MAINTENANCE
N2
N3
N5
N7
P1- 49S/49SE
P2 - BBC Only
Please note
If you have a machine fitted with BBC then you must
remove both blade bolts with a hexagonal drive key.
Always handle the blade with care - sharp edges
could cause injury.
USE GLOVES
Renew your metal blade after 50 hours mowing or 2
years whichever is the sooner - regardless of condition.
If the blade is cracked or damaged replace it with a
new one.
How to Charge the Battery (49SE ONLY)
1. Stop your lawnmower.
2. Disconnect the spark plug.
3. Remove the cap from the
charging point at the bottom
of the wiring loom (Q).
4. Plug charger lead into
connection on battery
loom
5. Plug the battery charger
into a domestic electric socket.
6. Charging will then commence.
7. Charge for 24 hours.
8. After charging, disconnect the charger from the
socket and charging point.
9. Replace the cap on the charging point.
10.The unit is now ready for use.
ENVIRONMENTAL INFORMATION
Electrolux Outdoor Products are manufactured under
an Environmental Management System (ISO 14001)
using, where practical, components manufactured in
the most environmentally responsible manner,
according to company procedures, and with the
potential for recycling at the end of the products' life.
• Packaging is recyclable and plastic components
have been labelled (where practical) for categorised
recycling.
• Awareness of the environment must be considered
when disposing of 'end-of-life' product.
• If necessary, contact your local authority for disposal
information.
BATTERY DISPOSAL
• The battery should be taken to an Approved Service
Centre or your local Recycling Station.
• Do NOT dispose of used battery with household
waste
• Lead/Acid batteries can be harmful and should
be disposed of through the recognised recycling
facility in accordance with European Regulation
• Do NOT dispose of battery to water.
• Do NOT incinerate
DISPOSAL OF FUELS AND LUBRICATING OILS
• Wear protective clothing when handling any fuels
and lubricants.
• Avoid contact with skin.
• Remove petrol and engine oil before transporting
the product.
• Contact your local authority for information of your
nearest Recycling/Disposal Station.
• Do NOT dispose of used fuels/oils with
household waste
• Waste fuels/oils are harmful, but can be
recycled and should be disposed of through the
recognised facilities.
• Do NOT dispose of used fuels/oils to water.
• Do NOT incinerate
Q
Wiring Loom
charging
cap
point