Auxiliary Functions - Beko WMB 51441 Mode D'emploi

Auxiliary functions

Auxiliary function selection
If an auxiliary function that should not be
selected together with a previously selected
function is chosen, the first selected function
will be cancelled and the last auxiliary function
selection will remain active.
Ex.: If you want to select pre-wash first and
then quick wash, pre-wash will be cancelled
and quick wash will remain active.
Auxiliary function that is not compatible with
the program cannot be selected. (see,
"Program Selection Table")
• Voorwas (Prewash)
When you select this function, the display will
indicate "F1" symbol.
• A pre-wash is only worthwhile for heavily
soiled laundry. Without pre-wash you save
energy, water, detergent and time.
• Pre-wash without detergent is
recommended for lace and curtains.
• Express Wassen (Quick Wash)
With this function, the wash time is shortened.
"F2" symbol lights up on the display.
• Use this function for smaller amounts or
slightly soiled laundries.
• Extra Spoelen (Rinse Plus)
When this function is selected, washing and
rinsing is performed with plenty of water. "F3"
symbol lights up on the display.
• Anti-kreuk (Anti-Creasing)
With this function, drum movement will be
lessened to prevent creasing and spinning
speed is limited. In addition, washing is carried
out at a higher water level. "F4" symbol lights
up on the display.
• Use this function for delicate laundries that
crease easily.
C Whenever you select this auxiliary function,
load your machine with half of the
maximum laundry specified in the program
table.
Time display
The display shows the time remaining for
the program to complete while a program
is running. Time is displayed in hours and
01:30
minutes as " ".
Time delay
With the "Time delay" function you can delay
the program start up to 24 hours. Setting can
be made in intervals of 30 minutes.
Open the loading door, place the laundry
inside and fill detergent drawer. Set the
washing program, temperature, spin speed
and, if required, select the auxiliary functions.
Press "Time delaying" buttons "+" and "-" to
set your desired time delay. The Time delaying
symbol will flash. Press "Start/Pause/Cancel"
button. Then the time delay starts to count
down. The Time delaying symbol will light up.
The Start symbol will light up.
The ":" in the middle of the displayed time
delay will start to flash.
•
More laundry may be loaded or taken out
during the time delay period. At the end of
the time delay countdown process, time
delaying symbol fades and the washing
starts as the program duration is displayed.
Changing the delay time
If you want to change the time during the
countdown:
Press "Start/Pause/Cancel" button. " : " in
the middle of the screen will stop flashing.
The Standby symbol will light up. The Time
delaying symbol will flash. The Start Symbol
will fade. Press "Time delaying" buttons "+" or
"-" to set your desired time delay. Press "Start/
Pause/Cancel" button. The Time delaying
symbol will light up. The Standby symbol will
fade. The Start symbol will light up.The ":" in
the middle of the displayed time delay will start
to flash.
Canceling the time delay
If you want to cancel the time delay
countdown and start the program immediately:
Press "Start/Pause/Cancel" button. The ":" in
the middle of the displayed time delay will stop
flashing. Start symbol will fade. The standby
symbol and the time delaying symbol will flash.
Press time delaying button "-" to decrease the
desired time delay. Program duration after 30
minutes shall be displayed. Press Start/Pause/
Cancel Button to start the program.
Starting the Program
Press Start/Pause/Cancel button to start the
program. The start symbol which indicates
that the program has started will light up.
The door locks and the door locked symbol
will light up. The Symbol of the relevant step
(prewash, main wash, rinse, softener and spin)
that the program has started from will light up.
Changing the selections after the
program has started
The selected spin speed and program
temperature fade out. An empty frame
appears.
When the "Program selection" button is
brought to the appropriate position, rpm and
temperature data reappear.
Switching the machine to standby mode
The machine is switched to standby mode
by pressing "Start/Pause/Cancel" button
momentarily. The Standby symbol which
indicates the machine is in standby mode
lights up and the start symbol that shows the
program has started and is still continuing
fades out.
51 - EN