Auxiliary Functions; Time Display; Starting The Program - Beko WMD 66160 Mode D'emploi

Auxiliary functions

Auxiliary Function Selection Buttons
Select the required auxiliary functions before
starting the program.
C
Some combinations cannot be selected
together. (Ex.: Pre-wash and Quick Wash.
Warning signal on the selected auxiliary function
will light up.
Auxiliary function selection
If an auxiliary function that should not be selected
together with a previously selected function
is chosen, the first selected function will be
cancelled and the last auxiliary function selection
will remain active.
(Ex.: If you want to select pre-wash first and then
quick wash, pre-wash will be cancelled and quick
wash will remain active.
Auxiliary function that is not compatible with the
program cannot be selected. (see, "Program
Selection Table")
C
Auxiliary function buttons may differ
according to the model of your machine.
Pre-wash
A pre-wash is only worthwhile for heavily soiled
laundry. Without pre-wash you save energy,
water, detergent and time.
C
Pre-wash without detergent is
recommended for lace and curtains.
Quick wash
This function can be used for "Cottons" and
"Synthetics" programs. It decreases the washing
times for lightly soiled laundries and also the
number of rinsing steps.
Rinse Plus
With this function, you can increase the number
of current rinsing steps. Thus, sensitive skins' risk
of being affected by the remainder detergent on
the clothes will be decreased.
Anti-creasing
With this function, drum movement will be
lessened to prevent creasing and spinning speed
is limited. In addition, washing is carried out at a
higher water level.
C
Whenever you select this auxiliary function,
load your machine with half of the
maximum laundry specified in the program
table.
No Heat
If you wish to wash your clothes in cold water,
you can use this program.

Time display

The display shows the time remaining for the
program to complete while a program is running.
Program duration may differ from the values in
the consumption table subject to the changes
in the water pressure, water hardness and
temperature, ambient temperature, type and
amount of laundry, auxiliary functions selected,
and changes in the supply voltage.
Time delay
With the "Time delay" function you can delay the
program start up to 24 hours. Time delay can be
set with steps of one hour for the first three hours
and with steps of three hours for the remainder
(1, 2, 3, 6, 9, ...24).
1. Pres "Time Delay" button to adjust the desired
time.
2. Press "Start/Pause/Cancel" button. The time
delay will start to count down.
C
More laundry may be loaded during the
time delay period.
Changing the delay time
If you want to change the time during the
countdown:
1. Press "Start/Pause/Cancel" button.
2. Pres "Time Delay" button to adjust the desired
time delay.
3. Press "Start/Pause/Cancel" button.
Canceling the time delay
If you want to cancel the time delay countdown
and start the program:
1. Press "Start/Pause/Cancel" button.
2. Pres "Time Delay" button to decrease the time
delay.
3. Press "Start/Pause/Cancel" button to start the
program.

Starting the Program

1. Press "Start/Pause/Cancel" button to start the
program.
2. Program follow-up lamp showing the startup
of the program will light up.
Progress of program
Progress of a running program is shown through
the program follow-up indicator. At the beginning
of every program step, the relevant indicator lamp
will light up and light of the completed step will
turn off. The symbol that is lit up at the far right
of the series of symbols indicates the step that is
being carried out.
C
If the machine is not spinning, the
program may be in rinse hold mode or
the automatic spin correction system
has been activated due to an excessive
unbalanced distribution of laundry in the
machine.
Changing the selections after the
program has started
Turning the program knob while the program is in
a normal flow will not change the program.
Switching the machine to standby mode
Press "Start/Pause/Cancel" button momentarily
to switch your machine to the standby mode.
Auxiliary functions can be cancelled or selected in
accordance with the step the program is at. The
8 - EN