Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Auxiliary functions
Auxiliary Function Selection Buttons
C
Select the required auxiliary functions
before starting the program.
C
Some combinations cannot be selected
together. (Ex.: Pre-wash) (Figure 1-5a) and
Quick Wash (Figure 1-5b).
Auxiliary function selection
If an auxiliary function that should not be
selected together with a previously selected
function is chosen, the first selected function
will be cancelled and the last auxiliary function
selection will remain active.
(Ex.: If you want to select pre-wash first and
then quick wash, pre-wash will be cancelled
and quick wash will remain active.
Auxiliary function that is not compatible
with the program cannot be selected. (see,
"Program Selection Table")
Pre-wash
When you select this function (5a), the display
will indicate "1" symbol. A pre-wash is only
worthwhile for heavily soiled laundry. Without
pre-wash you save energy, water, detergent
and time. Pre-wash without detergent is
recommended for lace and curtains.
Quick wash
With this function (5b), the wash time is
shortened. The "2" symbol will light up on the
display. Use this function for smaller amounts
or slightly soiled laundries.
Rinse plus
This function (5c) allows your machine to
perform an extra rinsing in addition to the
rinsing cycles performed by your machine after
main washing cycle. Thus, the risk for sensitive
skins (babies, allergic skins and etc.) to be
effected by the minimal detergent remnants on
the laundry is reduced. "3" symbol will light up
on the display.
Anti-creasing
With this function (5d), drum movement will
be lessened to prevent creasing and spinning
speed is limited. In addition, washing is carried
out at a higher water level. The "4" symbol will
light up on the display.
C
Whenever you select this auxiliary function,
load your machine with half of the
maximum laundry specified in the program
table.
Time display
The display shows the time remaining for
the program to complete while a program
is running. Program duration may differ
from the values in the consumption table
subject to the changes in the water pressure,
water hardness and temperature, ambient
temperature, type and amount of laundry,
auxiliary functions selected, and changes in
the supply voltage.
Time delay
With the "Time delay" function you can delay
the program start up to 24 hours. Setting can
be made in intervals of 30 minutes.
1. Press "Time delaying" buttons "+" and "-"
to set your desired time delay.
2. Press "Start/Pause/Cancel" button. Then
the time delay starts to count down.
C
More laundry may be loaded or taken out
during the time delay period.
Changing the delay time
If you want to change the time during the
countdown:
1. Press "Start/Pause/Cancel" button.
2. Press "Time delaying" buttons "+" or "-" to
set the desired time delay.
3. Press "Start/Pause/Cancel" button.
Canceling the time delay
If you want to cancel the time delay
countdown and start the program
immediately:
1. Press "Start/Pause/Cancel" button.
2. Pres "Time Delaying" "-" button to
decrease the time delay. Program duration
after 30 minutes shall be displayed.
3. Press "Start/Pause/Cancel" button to start
the program.
Starting the Program
1. Press "Start/Pause/Cancel" button to start
the program.
2. The start symbol (Figure 2-7j) which
indicates that the program has started will
light up.
3. The door locks and the door locked
symbol (Figure 2-7i) will light up.
4. The Symbol of the relevant step (prewash,
main wash, rinse, softener and spin) that
the program has started from will light up
(Figure 2-7f).
C
If the machine is not spinning, the
program may be in rinse hold mode or the
automatic spin correction system has been
activated due to an excessive unbalanced
distribution of laundry in the machine.
Changing the selections after the
program has started
The selected spin speed and program
temperature fade out. An empty frame
appears.
When the "Program selection" button is
8 - EN
Publicité
Table des Matières
