Forward-Facing Installation - NORAUTO 2274270 Mode D'emploi

7. Fasten the vehicle seat belt. You will hear an audible CLICK! Pull the seat belt tight to make sure it is not twisted.
EN
NOTE: For children of this size, the child seat must only be installed in the rearward facing position and at a maximum angle of inclination
(lying level). To make sure that the car seat has been installed correctly, please shake it before use.
DO NOT twist the belt! Ensure that the buckle tongues are properly locked into the vehicle seat buckle - you will hear an audible CLICK!
NOTE: Test by pulling on the child restraint and shoulder belt to ensure it is locked.

FORWARD-FACING INSTALLATION

Children from 9 to 36 kg (groups I, II, III) can ride in forward-facing direction.
GROUP I (9-18 KG)
1. Place child restraint forward-facing (in the direction of travel)
in proper seating location, flat on the vehicle seat bottom and
touching vehicle seat-back.
2. Pull out the support leg, and adjust it to the maximum angle.
3. Press the adjust button of the support leg, and adjust the length
of the support leg so that it is in full contact with the ground of
the vehicle. The display window turns into a green colour.
4. Select a forward-facing position from 1 to 4 (red).
5. Pull the shoulder belt section through belt guidance 2. Place
the lap belt section in the belt guidance 3.
6. Pull out safety belt from the back to the side, lap belt section
respectively from the belt guidance 3 of the base. One side of
the shoulder belt through the backrest and the belt guidance 3,
another side along the upper inside.
7. Fasten the vehicle seat belt. You will hear an audible CLICK! Pull
the seat belt tight to make sure it is not twisted.
8. By pressing your knee on the child seat, tighten the car belt as follows: pull on the lower part of the shoulder seat belt section near
the vehicle seat buckle to tighten the lap belt section.
NOTE: Test by pulling on the child restraint and shoulder belt to ensure it is locked.
GROUP II, III (15-36 KG)
NOTE: When using this child restraint in groups II or III, remove the 5-point harness, triangle pad, and sleeping pad.
1. Place child restraint forward-facing (in the direction of travel) in proper seating location, flat on the vehicle seat bottom and
touching vehicle seat-back.
2. Fold the support leg by pressing the adjuster button and slide it inside.
3. The support leg should hang. The display window turns into a red colour.
4. Select a forward-facing position 1 (red).
5. First, pull out the belt from the belt ALR. Shoulder belt through the same side of guidance 1, lap belt through the same side of
guidance 3. Then, pull the shoulder belt and lap
belt together through another side of guidance
3.
6. To fasten the seat belt across child: lap portion
of the vehicle seat belt should rest within both
lower belt guides with buckle located on the
outside of the child restraint.
7. Place shoulder portion into the upper belt
guide on the headrest so that belt lays properly
across child: on the collar bone, interior (A) to
the shoulder (B).
8. Make sure seat belt is not twisted and remove
slack from seatbelt so it lays flat, smooth and
snug across child in all locations.
9. Fasten the vehicle seat belt. You will hear an audible CLICK! Pull the seat belt tight to make sure it is not twisted.
CAUTION: The shoulder seat belt section must run diagonally backward. You can adjust the course of the belt with your vehicle's
adjustable belt deflector on both sides.
NOTE: Test by pulling on the child restraint and shoulder belt to ensure it is locked.
WARNING: If lap and shoulder belt portions of seat belt and seat belt buckle are not all correctly positioned, restraint is not properly
installed as a booster seat.
INSTALLATION WITH ISOFIX CONNECTOR
Confirm vehicle seating location has its own ISOFIX attachment points (see vehicle owner's manual). If you don't have the ISOFIX insert
guide, please ignore this step.
WARNING: If the child is not secured properly, the child could be ejected in a sudden stop or crash, resulting in serious injury or death.
WARNING: If in doubt about the installation, consult either the child restraint manufacturer or the retailer.
ISOFIX is the international standard of built-in attachment points in a car's structure to fit a child restraint. A child seat can easily be
plugged into the ISOFIX system which greatly reduces the risk of fitting the seat incorrectly. Many new vehicles have ISOFIX points built-in
when they are manufactured.
REAR-FACING INSTALLATION
It is recommended that children ride in a rear-facing child restraint until they are at least 2 years old. An infant's head, neck, and spine
are not supported as well in a forward-facing position.
GROUP 0+, I (0-18 KG)
1. Place child restraint rear-facing in a compatible vehicle seat.
2. Press the ISOFIX button to pull out the two ISOFIX locking arms from the base bottom.
the indicator turns into a red colour, which means ISOFIX attachments are unlocked.
NOTE: The ISOFIX attachment points are located between the surface and the backrest of the vehicle seat.
3. Align ISOFIX attachments to the metal anchorages at the bottom of the car seat's backrest and push it until it clicks.
an audible CLICK! Ensure both sides of the ISOFIX locking arms turn into green safety colour.
46
CLICK
A
B
CLICK
You will hear an audible CLICK! Ensure that
You will hear