Telephone Page; Telephone Numbers; Prefix; Digit To Remove - Bentel Security BGSM-G/AM Mode D'emploi

Telephone Page

The Telephone Page phonebook holds 95 telephone numbers.
, , , , , The first eight numbers in the phonebook will also be used for the SMS functions.

Telephone Numbers

† Description: enter an alphanumeric string of up to 20 characters.
† Number: enter a telephone number of up to 20 digits (only digits and "+" signs are accepted).
† Remote Control Numbers: select the telephone numbers which will be able to control Outputs 1, 2, 3 and 4 over the phone. The
telephone numbers cannot be selected in open order, therefore, if telephone numbers 1 and 6 are selected, telephone numbers 2,
3, 4 and 5 will be selected automatically.
† Dial.: This memorandum column shows the SMS Dialer telephone numbers (selected on the SMS Dialer Page from the first 8
telephone numbers in the phonebook).

Prefix

IMPORTANT: This Device will prefix the digits entered in this field to all the telephone numbers dialled through the GSM Interface
function.
If necessary enter a Prefix (maximum 4 digits) in this field. If no Prefix is required, leave this field empty.

Digit to Remove

If this Device is connected downstream to a switchboard, the telephone numbers (programmed on the Control panel) must be preceded
by the switchboard number (normally one digit). As the switchboard number is not required when calls are sent over the GSM Network,
it must be removed from the digits which form the telephone number. Enter the number of digits that form the switchboard number (e.g. if
switchboard number is 01, enter 2 in the 'Digits to remove' field, as 2 numbers form the switchboard number).

SMS Dialer Page

This page will allow you to program the SMS Dialer functions and Messages and also set up the 'Special Functions' of the 3 Input lines.
, , , , , The configuration data on on this page concerns the first eight telephone numbers entered on the "Telephone" page.
To send the SMS it is necessary enter a Customer Code (e.g. 1111) for the relevant event (see the column 'Customer
Code' in the Contact ID Page)

Main window

The column on the left-hand side of the Main window shows the events which, if duly programmed, will generate two SMS text messages: one
for activation and the other for restoral (the 'Periodic message' can generate the activation message only).
† Polarity: (this column shows the events which unbalance the 4 Input lines), select the Standby polarity of the Inputs
— H-Normally Open or L-Normally Closed.
† Telephone Numbers: click (tick) the check boxes of the numbers to be called when the respective event occurs.
† SMS: write the Activation and/or Restoral message to be sent when the respective event occurs (maximum 100 characters). If no
message is required, leave the respective box empty.
† Serv: If this option is enabled, unbalance (on Input Lines 1, 2 and 3) will generate actions instead of calls.
,QSXW OLQH QR 6HOHFW
 $
$

%
$

%
BGSM-G
,I WKLV RSWLRQ LV VHOHFWHG ² DQG ,QSXW /LQH  LV KHOG LQ D SHUPDQHQW VWDWH RI 8QEDODQFH WKLV 'HYLFH ZLOO
VHQG WKH 3HULRGLF 0HVVDJH DW UHJXODU LQWHUYDOV LQ DFFRUGDQFH ZLWK WKH YDOXHV LQ WKH 3HULRGLF 0HVVDJH VHFWLRQ 
,I ,QSXW /LQH  UHVWRUHV WR VWDQGE\ VWDWXV ,QSXW /LQH  EDODQFHG WKLV 'HYLFH ZLOO QRW VHQG WKH 3HULRGLF 0HVVDJH
,I WKLV RSWLRQ LV VHOHFWHG WKLV 'HYLFH ZLOO VHQG WKH 3HULRGLF 0HVVDJH LPPHGLDWHO\
5HVWRUH 5HVHUYHG 2XWSXWV WR 6WDQGE\
6SHFLDO )XQFWLRQV
6ZLWFK WR *60
(QDEOH'LVDEOH 3HULRGLF 0HVVDJH
6HQG 3HULRGLF 0HVVDJH QRZ
DQG VWDUW WKH LQWHUYDO EHWZHHQ PHVVDJHV
&OHDU &DOO 4XHXH
G G
G G G
25