Accessories - DeWalt DWS535B Guide D'utilisation

English
nOTE: When adding oil, allow the oil to flow very
slowly. Overflow may occur if the oil is added too
quickly.
5. Replace the oil plug and tighten securely.
6. Dispose of oil according to local, state and federal laws
and regulations.
Brushes (Fig. S)
Inspect carbon brushes regularly by unplugging the
saw, removing the end cap
24
adjustment lever and withdrawing the brush assembly.
2
Keep brushes clean and sliding freely in their guides. Always
replace a used brush in the same orientation in the holder
as it was prior to removal.
Carbon brushes have varying symbols stamped into their
sides, and if either brush is worn down to the line closest to
the spring, the brushes must be replaced. Use only identical
D WALT brushes. New brush assemblies are available at
e
your local service center. Always replace the end cap after
inspecting or servicing brushes.The tool should be allowed
to "run in" (run at no load without a blade) for 5 minutes
before use to seat new brushes. While "running in "DO NOT
TIE, TAPE, OR OTHERWISE LOCK THE TRIGGER SWITCH ON.
HOLD BY HAND ONLY.
Fig. S

Accessories


WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D WALT authorized service center.
e
Always use identical replacement parts.
12
located above the depth
24
2
WALT
e
WALT Industrial
e
WALT factory
e
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from
the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail
of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
433-9258). This warranty does not apply to accessories
or damage caused where repairs have been made
or attempted by others. THIS LIMITED WARRANTY IS
GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D
by our:
1 YEAR FREE sERViCE
D WALT will maintain the tool and replace worn parts
e
caused by normal use, for free, any time during the first year
after purchase.
90 DAY MOnEY BACK gUARAnTEE
If you are not completely satisfied with the performance of
your D WALT Power Tool, Laser, or Nailer for any reason, you
e
can return it within 90 days from the date of purchase with
a receipt for a full refund – no questions asked.
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1-800-4-D
(1-800-433-9258) for a free replacement.
WALT (1-800-
e
WALT tools are covered
e
WALT
e