Scheppach HM100MP Traduction Du Manuel D'origine page 26

and release the ON/OFF button (2).
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not re-
lease the handle (1) after completing the cut; instead
allow the machine head to move upwards slowly
whilst applying light counter pressure.
8.5 Cross cut 90° and turntable 0° - 45° (Fig. 1,6,7)
The crosscut saw can be used to make crosscuts of 0°
-45° to the left and 0° -45° to the right in relation to the
stop rail.
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (28) must be fixed in the outer posi-
tion.
• Open the set screw (29) on the moveable stop rail
(28) and push the moveable stop rail (28) outwards.
• The moveable stop rail (28) must be locked in a po-
sition far enough from the inner position that the dis-
tance between the stop rail (28) and the saw blade
(7) is no more than 5 mm.
• Before making the cut, check that no collision could
occur between the stop rail (28) and the saw blade (7).
• Tighten the set screw (29) again. (2x 8.6 + 8.7)
• Use the handle (13) to adjust the rotary table (16)
to the desired angle. The pointer (14) on the rotary
table (16) must match the desired angle on the scale
(15) on the fixed saw table (17).
• Tilt the locking lever (13) back up again to fix the ro-
tary table (16) in place.
• Cut as described under section 8.3.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1,2,6,8)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28) must be fixed at the outer
position.
• Open the locking lever (29) for the adjustable stop
rail (28) and push the adjustable stop rail outwards.
• The adjustable stop rail (28) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (28) and the saw
blade (7) amounts to a maximum of 5 mm.
• Before making a cut, check that the stop rail (28)
and the saw blade (7) cannot collide.
• Secure the locking lever (29) again.
• Move the machine head (5) to the top position.
• Fix the rotary table (16) in the 0° position.
• Loosen the set screw (22) and use the handle (1)
to angle the machine head (5) to the left, until the
pointer (20) indicates the desired angle measure-
ment on the scale (19).
• Re-tighten the fixing screw (22).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 1,2,6,9)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the
right in relation to the stop rail (double mitre cut).
26 GB
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28) must be fixed at the outer
position.
• Open the locking lever (29) for the adjustable stop
rail (28) and push the adjustable stop rail outwards.
• The adjustable stop rail (28) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (28) and the saw
blade (7) amounts to a maximum of 5 mm.
• Before making a cut, check that the stop rail (28)
and the saw blade (7) cannot collide.
• Secure the locking lever (29) again.
• Move the machine head (5) to its upper position.
• Release the rotary table (16) by loosening the set
screw (26).
• Using the handle (13), set the rotary table (16) to the
desired angle (refer also to point 8.4 in this regard).
• Re-tighten the set screw (26) in order to secure the
rotary table.
• Undo the locking screw (22) and use the handle (1)
to tilt the machine head (5) to the left until it coin-
cides with the required angle value (in this connec-
tion see also section 8.6).
• Re-tighten the fixing screw (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3)
• The cutting depth can be infinitely adjusted using the
screw (26). To do this loosen the knurled nut on the
screw (26). Turn the screw (26) in or out to set the
required cutting depth. Then re-tighten the knurled
nut on the screw (26).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (21) for saw-
dust and chips.
Squeeze together the metal ring on the dust bag and
attach it to the outlet opening in the motor area.
The debris bag (21) can be emptied by means of a zip-
per at the bottom.
8.10 Changing the saw blade (Fig. 11-15)
Remove the power plug!
Important.
Wear safety gloves when changing the saw blade.
Risk of injury!
• Remove the spring (41) from the pin by pushing to-
gether the two ends.
• Release the guide bar (40) from the pin.
• Firmly press the saw shaft lock (4), and slowly turn
the flange screw (32) clockwise. After max. one turn,
the saw shaft lock (4) engages.
• Then undo the flange screw (32), by applying a
slightly greater force in a clockwise direction.
• Fully unscrew the flange screw (32) and remove the
outer flange (33).
• Press the unlocking lever (3) to slide back the saw
blade guard (6), then remove the saw blade (7) from
the inner flange (39) and pull out in a downwards
direction.
• Carefully clean the flange screw (32), outer flange