Troubleshooting Guide - DeWalt DCH733 Guide D'utilisation

English
2 YEARs FREE sERViCE
D WALT will maintain the tool and replace worn parts
e
caused by normal use, for free, any time during the first two
years after purchase.
2 YEARs FREE sERViCE On DEWAlT BATTERY PACKs
DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,
DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361
3 YEARs FREE sERViCE On DEWAlT BATTERY PACKs
DCB200, DCB204, DCB204BT, DCB205, DCB205BT, DCB206,
DCB606, DCB609
nOTE: Battery warranty voided if the battery pack is
tampered with in any way. D
for any injury caused by tampering and may prosecute
warranty fraud to the fullest extent permitted by law.
90 DAY MOnEY BACK gUARAnTEE
If you are not completely satisfied with the performance of
your D WALT Power Tool, Laser, or Nailer for any reason, you
e
can return it within 90 days from the date of purchase with
a receipt for a full refund – no questions asked.
For assistance with your product, visit our website at www.dewalt.com for a list of service centers, or call D
1-800-4-D WALT (1-800-433-9258).
e
PROBlEM
Tool will not start.
Reduced Power.
The bit does not rotate.
The bit cannot be released.
The yellow service indicator light is
on or flashing.
Tool shuts off abruptly.
Battery pack will not charge.
12
WALT is not responsible
e

TROUBLESHOOTING GUIDE

BE sURE TO FOllOW sAFETY RUlEs AnD insTRUCTiOns
POssiBlE CAUsE
Battery pack not installed properly.
Battery pack not charged.
Internal componets too hot.
The speed dial is set to a lower setting.
Battery has low state of charge.
The mode selector dial is not correctly engaged,
or is set to "Hammering Only" or is set to
position "O".
The chuck is not pulled back fully.
The time for service has been reached.
Battery pack has reached its maximum
thermal limit.
Out of charge. (To maximize the life of the
battery pack it is designed to shut off
abruptly when the charge is depleted.)
Battery pack not inserted into charger.
Charger not plugged in.
Surrounding air temperature too hot or
too cold.
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1-800-4-D
(1-800-433-9258) for a free replacement.
sOlUTiOn
Check battery pack installation.
Check battery pack charging requirements.
Allow tool to cool down.
Rotate the speed dial to a higher setting suitable for
the application.
Replace with fresh battery pack.
Rotate the mode selector dial to "Rotary Hammering". Refer to
Operation Modes.
Pull the chuck back as far as it will go and remove the bit. Refer
to Inserting and Removing SDS MAX Bits.
Have service perfomed by an authorized D
if necessary. Refer to E-Clutch® and Service Indicator LEDs.
Allow battery pack to cool down.
Place on charger and allow to charge.
Insert battery pack into charger until LED illuminates.
Plug charger into a working outlet. Refer to Important
Charging Notes for more details.
Move charger and battery pack to a surrounding air temperature
of approximately 65 °F – 75 °F (18 °C– 24 °C).
WALT
e
WALT at
e
WALT service center
e