Troubleshooting Guide - DeWalt D25733 Guide D'utilisation

English
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from
the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail
of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
433-9258). This warranty does not apply to accessories
or damage caused where repairs have been made
or attempted by others. THIS LIMITED WARRANTY IS
GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
For assistance with your product, visit our website at www.dewalt.com for a list of service centers, or call D
1-800-4-D WALT (1-800-433-9258).
e
PROBlEM
Tool will not start.
Reduced Power
The bit does not rotate.
The bit cannot be released.
The yellow or red service indicator
lights are on or flashing.
8
WALT (1-800-
e

TROUBLESHOOTING GUIDE

BE sURE TO FOllOW sAFETY RUlEs AnD insTRUCTiOns
POssiBlE CAUsE
The extension cord and/or plug is defective.
Internal componets too hot.
Brushes worn out.
The extension cord is too long and/or its gauge
is inadequate.
The speed dial is set to a lower setting.
The voltage provided by the electric supply
is inadequate.
The mode selector dial is not correctly engaged,
or is set to "Hammering Only" or is set to
position "O".
The chuck is not pulled back fully.
The carbon brushes are nearly worn or the time
for service has been reached.
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D
by our:
2 YEARs FREE sERViCE
D WALT will maintain the tool and replace worn parts
e
caused by normal use, for free, any time during the first two
years after purchase.
90 DAY MOnEY BACK gUARAnTEE
If you are not completely satisfied with the performance of
your D WALT Power Tool, Laser, or Nailer for any reason, you
e
can return it within 90 days from the date of purchase with
a receipt for a full refund – no questions asked.
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1-800-4-D
(1-800-433-9258) for a free replacement.
sOlUTiOn
Have the extension cord and/or plug checked by a qualified
electrician and replaced if necessary.
Allow tool to cool down.
Have brushes replaced by an authorized D
Use an extension cord of an approved length and/or of
adequate gauge.
Rotate the speed dial to a higher setting suitable for
the application.
Connect the hammer to an adequate electric supply.
Rotate the mode selector dial to "Rotary Hammering". Refer to
Operation Modes.
Pull the chuck back as far as it will go and remove the bit. Refer
to Inserting and Removing SDS MAX Bits.
Have tool service performed by an authorized D
center. Refer to E-Clutch® and Service Indicator LEDs.
WALT tools are covered
e
WALT
e
WALT at
e
WALT service center.
e
WALT service
e