DeWalt DCD792 Guide D'utilisation page 12

English
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury. Exception—Tool
Connect™ functions and mode adjustments require
battery to be installed.
Mode Selector (Fig. A, J)

WARNING: To reduce the risk of injury, remove
accessories from the tool chuck before using the
mode selector.
Your tool is equipped with a mode selector that allows 3
modes to be customized using the Tool Connect™ app.
Home settings are active when the home indicator
lit. The following 3 features can be customized. For more
information, refer to Table 1 below.
Once configured, pressing the mode selector button
the foot of the tool will cycle through the modes
If you are unsure of the current configuration, press the
mode selector button 12 to set the tool to the Home
setting (home indicator is lit).
13
Fig. J
12 13
D WALT Tool Connect™
e

WARNING: To reduce the risk of injury, remove
accessories from the tool chuck before any Tool
Connect™ interaction.
NOTICE: Always check the tool configuration prior
to use. If you are unsure of the current configuration,
press the mode selector button
tool to the Home setting as described on the label and
this manual.
Table 1
Customizable Features
Worklight brightness
Worklight delay off
Maximum speed (RPM)
10
is
13
12 on
14 .
14
12 (Fig. J) to set the
Home Mode 1
MED
20 secs 20 secs
Speed 1 550
Speed 2 2000 2000
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://
www.bluetooth.com/Pages/Bluetooth-Smart-Devices-List.
aspx)
D WALT Tool Connect™ is an application for your smart
e
device (such as a smart phone or tablet) that connects the
device to your tool to allow you to configure specific tool
functions. Refer to Mode Selector.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use
of such marks by D WALT is under license. Other trademarks
e
and trade names are those of their respective owners.
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D WALT Tool Connect™ application at:
e
• Follow the instructions in the app to create your Tool
Connect™ account.
• On the Home screen of the app, select "+ Tool" to begin
the process of adding your tool to the app.
• To connect your tool with the D
app, at the appropriate screen, press the mode selector
button 12 for 3–5 seconds, then wait for the tool to
connect. The tool can only be connected to one Tool
Connect™ account at a time.
• Once the tool has been connected, you can confirm that
you would like to register the product.
For more information on D
functionality and features, please call 1–800–4-D
(1–800–433–9258), visit www.dewalt.com or view
the FAQ page and help screens located inside the
mobile application.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your
local D WALT service center. Do not attempt to replace the
e
coin cell battery yourself.

WARNING: Danger of explosion if battery is
incorrectly replaced.

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/
button cell battery. If the coin/button cell battery is
Factory Presets
Mode 2 Mode 3
OFF MED HIGH
20 secs 20 minutes
550 550 550
2000 2000
WALT Tool Connect™
e
WALT Tool Connect™
e
WALT
e
Customizable Range
OFF–HIGH
0–20 minutes
180–550
600–2000