Part Names And Functions - Denon DN-S3000 Mode D'emploi

ENGLISH

PART NAMES AND FUNCTIONS

3
(1) Front panel
q
Disc loading slot
• Load the disc slowly, and release it once the
DN-S3000 starts grabbing the disc in.
CAUTIONS:
• Do not load discs when the power is turned
off.
• Do not try to forcibly remove a disc once
the DN-S3000 has started to grab the disc.
• Do not load more than once disc at a time
or insert anything other than discs.
Otherwise loading mechanism may be
damaged.
w
CD drive
• This Drive is field replaceable by you.
• Optional spare drive is sold separately.
8
(2) Rear panel
e
POWER button (¢ON £OFF)
• Push this button to turn power on and off.
CAUTION:
• Do not turn off the power while a disc is
loading or being ejected. Otherwise loading
mechanism may be damaged.
r X-EFFECT jacks
(X-EFFECT IN/OUT)
• Connect this jack to the DENON mixer DN-
X800 and DN-S3000 with 3.5 mm stereo mini
cord.
t
Analog output jacks
(LINE OUT)
• This is unbalanced RCA output jacks.
• Audio signals outputs.
y
Fader start jack
• Use this when your mixer has Fader Start
function with 3.5 mm stereo mini cord.
u
Digital output jack
• Digital data is available from this jack.
• Use 75 Ω/ohms pin cord for connection.
• We recommend you use braided wire type
shielded cable.
NOTE: The playback level after analog
conversion is set to -6dB of the usual
level.
(3) Top panel
CAUTION:
• Note that there are many buttons working two
different function selected by short time
pushing or long pushing (1second or more). The
mark indicates short time push function and
mark indicates long time push function.
i
Play/Pause button (13)
• This button will start or pause playback.
• Push once to start playback, once again to
pause playback, and once more to resume
playback.
o
DISC EJECT button
• Eject disc with this button while button
illumination light. Note that if illumination is off,
you cannot eject disc.(Eject lock function)
!0
CUE button
• Pushing this button in play mode will force the
track back to the position which playback
started. While in search mode, it makes new
Cue point. (Cue)
• In Cue mode, by pushing the CUE button
makes a Stutter sound from the Cue point. This
is called Stutter play. (Stutter)
!1
Platter/Scratch Disc
Use this vinyl scratch disc for manual search,
Pitch Bend and Scratch operations.
• Platter:
The Platter turns when playback of the source
select Scratch mode button is in the Main or
Sampler position and in play mode.
• Scratch Disc:
When the Scratch Disc is turning, Scratch
playback of the source selected (Main or
Sampler) starts.
NOTE: The Platter does not turn when the
Scratch mode is set to the SEARCH
mode. If "PLATTER TURN STOP" is
selected within the presets, the Platter
never turns, regardless of the Scratch
mode.
However, you still may be able to
scratch normally without the platter
spinning.
When using the player in this mode,
there will a small delay upon release of
the scratch disc. (This is normal)
To avoid this delay, press the PLAY
button simultaneously upon release of
the scratch disc with your thumb.
CAUTIONS:
• Do not forcibly try to stop the Platter when
it is turning. Otherwise Platter moving
mechanism may be damaged.
• If a problem with Platter rotation arises
when the Platter is turning, the Platter
stops turning and the pause mode is set.
!2
FLIP/CLR button
• FLIP:
Use this to select operating mode of A button,
from Hot Start mode and Stutter mode. FLIP
LED lights up in Hot Start mode.
• A CLR:
If the A button is pushed while pushing the
FLIP button, you can clear the A point.
Or, by holding down just the FLIP button for
more than 1 sec.
!3
(SAMP) RVS/CLR button
• (SAMP)RVS:
Use this to select the sample play direction
forward and reverse. When select reverse
RVS LED lights up.
• (SAMP) CLR:
If the SAMP button is pushed while pushing
the FLIP button, you can clear the SAMP data.
Or, by holding down just the FLIP button for
more than 1 sec.
!4
A button
• Using this button you can create starting point
for Hot Start, Seamless Loop and Stutter.
!5
SAMP button
• Push this button to record or play sound of
Sampler.
!6
B button
• Use this to set the B point for A point of
Seamless Loop.
!7
(SAMP) B button
• Use this to set the Sampler loop B point.
!8
EXIT/RELOOP button
• Use this to exit or return back again to
Seamless loop playback. You can add variety
to looping with this function.
• The LED indicates what's going on about
looping.
EXIT/RELOOP LED lit:
Seamless Loop on or playing.
EXIT/RELOOP LED flashing:
Playback after exit loop.