Part Names And Functions - Denon DN-S1000 Mode D'emploi

ENGLISH

PART NAMES AND FUNCTIONS

3
(1) Front panel
q
Disc loading slot
• Load the disc slowly, and release it once the
DN-S1000 starts grabbing the disc in.
NOTE:
Please clean the dirt of the label side of a disc
and start loading of the disc.
The dirt causes a slip of a disc loader roller.
CAUTIONS:
• Do not load discs when the power is turned
off.
• Do not try to forcibly remove a disc once
the DN-S1000 has started to grab the disc.
• Do not load more than once disc at a time
or insert anything other than discs.
Otherwise loading mechanism may be
damaged.
8
(2) Rear panel
w
POWER button (¢ON £OFF)
• Push this button to turn power on and off.
CAUTION:
• Do not turn off the power while a disc is
loading or being ejected. Otherwise loading
mechanism may be damaged.
e
Analog output jacks
(LINE OUT)
• This is unbalanced RCA output jacks.
• Audio signals outputs.
r
Fader start jack
• Use this when your mixer has Fader Start
function with 3.5 mm stereo mini cord.
t
Digital output jack
• Digital data is available from this jack.
• Use 75 Ω/ohms pin cord for connection.
• We recommend you use braided wire type
shielded cable.
NOTE: The playback level after analog
conversion is set to –6dB below the
usual level to avoid digital distortion.
(3) Top panel
CAUTION:
• Note that there are many buttons working two
different function selected by short time
pushing or long pushing (1 second or more). The
mark indicates short time push function and
mark indicates long time push function.
y
PLAY/PAUSE button (13)
• This button will start or pause playback.
• Push once to start playback, once again to
pause playback, and once more to resume
playback.
u
DISC EJECT button
• Push this button to eject the disc.
• The disc will not eject during playback.
Stop playback before pushing this button.
i
CUE button
• Pushing this button in play mode will force the
track back to the position which playback
started. While in search mode, it makes new
Cue point. (Cue)
• In Cue mode, by pushing the CUE button
makes a Stutter sound from the Cue point. This
is called Stutter play. (Stutter)
o
Scratch Disc
Use this vinyl scratch disc for scan, manual
search, Pitch Bend and Scratch operations.
!0
FLIP/CLR button
• FLIP:
Use this to select operating mode of A1 and A2
buttons, from Hot Start mode and Stutter
mode. The display will indicate "H/S" or "STR"
• A1, A2 CLR:
If the A1 or A2 button is pushed while pushing
the FLIP button, you can clear the selected A
point.
By holding down just the FLIP button for more
than 1 sec, you can clear A1 and A2 points all
at once.
!1
A1, A2 button
• Using this button you can create starting point
for Hot Start, Seamless Loop and Stutter.
!2
B button
• Use this to set the B point to create a
Seamless Loop after the A point has been set.
!3
EXIT/RELOOP button
• Use this to exit or return back again to
Seamless loop playback. You can add variety to
looping with this function.
!4
NEXT TR./B TRIM button
• When the button is pressed during playback,
the NEXT TRACK MODE is selected. If the
button is pressed again, the B TRIM MODE is
selected.
In the standby and pause modes, only the B
TRIM MODE can be selected.
!5
TITLE button
• CD TEXT:
When there is CD text data, the CD text data
is displayed automatically or when the button
is pressed.
If no TEXT is available, the display will indicate
"No TEXT".
• MP3:
When an MP3 file has ID-3 tag data, the title,
artist name and album name are selected and
displayed each time the button is pressed.
!6
TIME, CONT./SINGLE button
• TIME:
A short push will displays mode changes
between ELAPSED TIME and REMAIN TIME.
• 4-way TOTAL TIME display mode can be
selected by PRESET(8).
• At this time, you can select display mode from
four modes, TRACK ELAPSED, TRACK
REMAIN, DISC ELAPSED and DISC REMAIN.
• CONT./SINGLE:
Long pushing play ending mode between
CONT. (continue: play more tracks) and
SINGLE (stop playing and ReCUE's back to
your set point).
• SINGLE PLAY LOCK:
When SINGLE PLAY LOCK is selected, track
selection during playback is disabled. This
prevents playback from stopping when the
Track Select Knob is turned accidentally during
playback. Play ending mode is the same as
single mode.
!7
MEMO, PRESET button
• MEMO:
The memo mode starts when this button is
pushed once in the Cue mode.
• PRESET:
When this button is pushed for more than 1
sec, the PRESET mode menu is displayed.
The machine status must be in, CUE, PAUSE
or No Disc mode before entering the preset
mode.