Troubleshooting; Side Burner Troubleshooting - Weber SUMMIT GRILL CENTER Mode D'emploi

PROBLEM
Burners burn with a yellow or orange flame, in
conjunction with the smell of gas. (This is normal for
the burner lighting tube.)
Symptoms:
Burners do not light.
OR
Burners have a small, flickering flame in the HI
position.
OR
Barbecue temperature only reaches 250° to 300° in
the HI position.
Burner does not light.
OR
Flame is low in HI position.
Experiencing flare-ups:
m CAUTION: Do not line the slide-out
grease tray with aluminum foil.
Burner flame pattern is erratic. Flame is low when
burner is on HI. Flames do not run the whole length
of the burner tube.
Inside of lid appears to be "peeling." (Resembles
paint peeling.)
Cabinet doors are not aligned.
Barbecue seems to lose heat when cooking in cold
weather temperatures of 50°F or colder.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
PROBLEM
Side Burner does not light.
Flame is low in HI position.
Push button ignition does not work.
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact information on our
web site. Log onto www.weber.com
40

TROUBLESHOOTING

Inspect spider/insect screens for possible obstructions .
(Blockage of holes .)
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have been
activated .
Is LP fuel low or empty?
Is fuel hose bent or kinked?
Does burner light with a match?
Did you use the snap igniter several times until the main
burner lit? Refer to "MAIN BURNER IGNITION . "
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
Are you preheating barbecue in the prescribed manner?
Are the cooking grates and Flavorizer
coated with burned-on grease?
Is the slide-out grease tray "dirty" and not allowing
grease to flow into catch pan?
Are burners clean?
The lid is porcelain enamel or stainless steel, not paint .
It cannot "peel . " What you are seeing is baked-on grease
that has turned to carbon and is flaking off .
THIS IS NOT A DEFECT.
Check the adjustment pin on the bottom of each door .
Is there frost/ice on the outside of the LP cylinder?
.
®

SIDE BURNER TROUBLESHOOTING

Is gas supply off?
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have activated .
Is the fuel hose bent or kinked?
Does burner light with a match?
® .
CHECK
bars heavily
®
CHECK
SOLUTION
Clean spider/insect screens . Refer to "ANNUAL
MAINTENANCE . "
To reset the excess flow safety device, turn all burner
control knobs and the cylinder valve off . Disconnect the
regulator from the cylinder . Turn burner control knobs
to HI . Wait at least one minute . Turn burner control
knobs to OFF . Reconnect the regulator to the cylinder .
Turn cylinder valve on slowly . Refer to "MAIN BURNER
IGNITION . "
Refill LP cylinder .
Straighten fuel hose .
Clean burners . Refer to "MAINTENANCE . "
Make sure to hold the control knob in for two seconds
after snapping the igniter and seeing the orange flame
from the burner lighting tube .
Try manually lighting the burner . Refer to "MAIN
BURNER MANUAL IGNITION . " Call Customer Service .
Turn all burners on HI for 10 to 15 minutes for preheating .
Clean thoroughly . Refer to "CLEANING . "
Clean slide-out grease tray .
Clean burners . Refer to "MAINTENANCE . "
Clean thoroughly . Refer to "CLEANING . "
Loosen adjustment nut/s . Slide door/s until aligned .
Tighten nut/s .
The liquid propane in the cylinder turns to vapor too
slowly to supply the burners with gas . This is due to the
air temperature cooling the LP cylinder, which slows the
vaporization process . Turn off burner control knobs and
the LP cylinder . Replace with a spare LP cylinder and
resume cooking .
SOLUTION
Turn gas supply on .
To reset the excess flow safety device close the LP
tank valve and turn all burner control knobs to the OFF
position . Open the grill and side burner lids . Slowly turn
the LP tank valve until it is completely open . Wait several
seconds then ignite your side burner . Refer to "SIDE
BURNER IGNITION" .
Straighten hose .
If match lights burner, check igniter . Refer to "SIDE
BURNER MAINTENANCE" .