Publicité
Les langues disponibles
Les langues disponibles
English
of masonry materials at various work sites (i.e.,
construction sites).
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
Your heavy-duty small angle grinders is a professional
power tool. DO nOT let children come into contact with the
tool. Supervision is required when inexperienced operators
use this tool.
Features
DWE46202
E-switch Protection™
The ON/OFF switch has a no-volt release function. In the
event of a power outage or other unexpected shut down,
the switch will need to be cycled (turned off and then on)
to restart tool.
E-Clutch™
This unit is equipped with an E-Clutch™ (Electronic Clutch),
which in the event of a high-load or wheel pinch, the unit
will be shut off to reduce the reaction torque to the user.
The switch needs to be cycled (turned off and then on) to
restart tool.
Brake
When the switch is released the motor immediately turns
off and electronically brakes stopping the accessory quickly.
Kickback Brake™
When a severe pinch, stall, or bind-up event is sensed the
electronic brake engages with maximum force to quickly
stop the wheel, reduce the movement of the grinder, and
shut the grinder off. The switch needs to be cycled (turned
off and then on) to restart tool.
Constant Clutch™
When overloaded or stalled the motor torque is reduced. If
load is reduced the torque and RPM will increase. If the tool
is stalled for an extended amount of time it will shut-off and
require the switch to cycle to restart.
Variable Speed Dial (Fig. A)
WARNING: Regardless of the speed setting, the rated
speed of the accessory must be at least equal to the
maximum speed marked on the power tool.
The variable speed dial offers added tool control and
enables the tool to be used at optimum conditions to suit
the accessory and material.
•
Turn the dial
to the desired level. Turn the dial to the
7
right for higher speed and to the left for lower speed.
LED Indicator (Fig. A)
The LED indicator
8
will remain lit green during normal
activity, or blink in a pattern of red light to alert you a
tool protection feature has been activated. Refer to the
LED Guide at the back of this manual for explanations of
blink patterns.
6
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Accessories
The capacity for this shroud is 6" (150mm) diameter x 1/4"
(6.35mm) diamond coated steel wheel (diamond wheel).
It is important to choose the correct guards, backing pads
and flanges to use with grinder accessories. See page 10 for
information on choosing the correct accessories.
WARNING: Handle and store all abrasive wheels
carefully to prevent damage from thermal shock, heat,
mechanical damage, etc. Store in a dry protected area
free from high humidity, freezing temperatures or
extreme temperature changes.
Attaching Side Handle (Fig. A)
WARNING: Before using the tool, check that the
handle is tightened securely.
Screw the side handle
5
tightly into one of the holes on
either side of the gear case. The side handle should always
be used to maintain control of the tool at all times.
Guards
CAUTION: Guards must be used with all grinding
wheels, cutting wheels, sanding flap discs, wire
brushes, and wire wheels. Refer to Figure A to see
guards provided with the unit. Some applications
may require purchasing the correct guard and other
components from your local dealer or authorized
service center.
nOTE: The tuckpointing shroud is only to be used
in tuckpointing and cutting masonry materials with
diamond wheels.
nOTE: See the Accessories Chart to select the proper
guard / accessory combination.
Mounting and Removing Tuckpoint
Shroud (Fig. B)
1. Loosen the collar screw
11
and align the tabs
21
on the tuckpoint shroud with the
slots
22
on the grinder gear case.
Fig. B
21
on the tuckpoint shroud
11
22
Publicité
