Publicité
Les langues disponibles
Les langues disponibles
accidental unplugging, or power failure. If the slider
switch is locked on when the power is connected, the
tool may start unexpectedly.
To start the tool, slide the ON/OFF slider switch
the front of the tool using the rear portion of the switch. To
stop the tool, release the ON/OFF slider switch.
For continuous operation, slide the switch toward the front
of the tool and press the forward part of the switch inward.
To stop the tool while operating in continuous mode, press
the rear part of the slider switch and release.
Spindle Lock (Fig. A)
The spindle lock
2
is provided to prevent the spindle from
rotating when installing or removing wheels. Operate the
spindle lock only when the tool is turned off, unplugged
from the power supply, and has come to a complete stop.
NOTICE: To reduce the risk of damage to the tool, do
not engage the spindle lock while the tool is operating.
Damage to the tool will result and attached accessory
may spin off possibly resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate the
spindle further.
Tuckpointing and Masonry Cutting
Application (Fig. G)
1. Set the desired depth of cut, see Depth of Cut
Adjustment under Assembly and Adjustments.
2. Allow the tool to reach full speed before touching it to
the work surface.
3. Position yourself so the open underside of the shroud
and the wheel are facing away from you.
4. Place the edge
20
of shroud onto the work surface and
begin cut by plunging into the work surface.
nOTE: Keep the edge
20
work surface to ensure proper dust collection.
5. With the shroud oriented as shown in Figure G, move
the grinder right to left along the work surface. For the
best results the grinder should be positioned at a 45°
angle to the dust port when tuckpointing/cutting.
6. Remove the tool from work surface before turning off
the tool. Allow the tool to stop rotating before laying
it down.
Masonry Edge Grinding and Cutting (Fig. H)
WARNING: Do not use edge grinding/cutting wheels
for surface grinding applications because these wheels
are not designed for side pressures encountered
with surface grinding. Wheel breakage and injury
may result.
CAUTION: Wheels used for edge grinding and cutting
may break or kick back if they bend or twist while
the tool is being used. In all edge grinding/cutting
operations, the open side of the shroud must be
positioned away from the operator.
1. Allow the tool to reach full speed before touching the
tool to the work surface.
6
toward
of the shroud against the
2. Apply minimum pressure to the work surface, allowing
the tool to operate at high speed. Grinding/cutting rate
is greatest when the tool operates at high speed.
3. Position yourself so that the open-underside of the
wheel is facing away from you.
4. Once a cut is begun and a notch is established in
the workpiece, do not change the angle of the cut.
Changing the angle may cause wheel breakage.
Fig. H
5. Remove the tool from the work surface before turning
the tool off. Allow the tool to stop rotating before laying
it down.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by D
WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
English
WALT
e
WALT Industrial
e
9
Publicité
