EINHELL TE-ID 1050 CE Mode D'emploi D'origine page 19

5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning! Always pull the power plug before
making adjustments to the equipment.
5.1. Fitting the additional handle (Fig. 2-3/
Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do
not use the tool without the additional handle.
The additional handle (8) is secured to the ham-
mer drill by a clamp. During the handle clockwise
tightens this clamp. Turning it anti-clockwise will
release the clamp.
•
The supplied additional handle (8) must
first be fitted. To do this, the clamp must be
opened by turning the handle until it is wide
enough for the additional handle to be slid
over the chuck (1) and on to the hammer drill.
•
After you have positioned the additional
handle (8), turn it to the most comfortable
working position for you.
•
Now turn the handle in the opposite direction
again until the additional handle is secure.
•
The additional handle (8) is suitable for both
left-handed and right-handed users.
5.2 Fitting and adjusting the depth stop
(Fig. 4/Item 2)
•
Undo the thumb screw (a) on the additional
handle (8) and insert the depth stop (2) in the
hole of the additional handle.
•
Set the depth stop and retighten the thumb
screw.
•
Now drill the hole until the depth stop touches
the workpiece.
5.3 Fitting the drill bit (Fig. 10)
Always pull the power plug before making adjust-
ments to the equipment.
•
Release the depth stop as described in 5.2
and push it towards the additional handle.
This provides free access to the chuck (1).
•
This hammer drill is fitted with a keyless
chuck (1).
•
Open the chuck (1). The drill bit opening must
be large enough to fit the drill bit into.
•
Select a suitable drill bit. Push the drill bit as
far as possible into the chuck opening.
•
Close the chuck (1). Check that the drill bit is
secure in the chuck (1).
Anleitung_TE_ID_1050_CE_SPK7.indb 19 Anleitung_TE_ID_1050_CE_SPK7.indb 19
GB
•
Check at regular intervals that the drill bit or
tool is secure (pull the mains plug).
5.4 Fitting the dust extraction system (Fig.
5-9)
The dust extraction system (11) is fi tted on the
additional handle (8). It can also be used in com-
bination with the depth stop (2). This prevents the
work area becoming very dirty.
•
Release the cover (A) and the sealing cap (B)
by turning the additional handle (8). Several
drill bits can be stored in the sealing cap (B)
to save space (Fig. 5-6).
•
Screw the dust extractor adapter (9) on to the
additional handle (8) from underneath.
•
Now place the dust extraction system (11) on
to the additional handle (8) as shown in Fig.
7 – 8 and secure it by turning it.
Important. There are detents on the cover (A)
and the dust extraction system (11) which
must be engaged in the corresponding re-
cesses on the additional handle (8) before
the cover (A) or dust extraction system (11)
can be turned and locked.
•
Remove the dust extraction system (11) by
following the above in reverse.
•
Fit the additional handle (8) on the machine
as described in 5.1. Please note that the
additional handle (8) must be fitted to the left-
hand side of the machine if the dust extrac-
tion system (11) is also fitted (Fig. 9).
•
The dust extraction system (11) can be fitted
to the machine even if the additional handle
(8) is fitted.
•
If the dust extraction system (11) is not re-
quired, the cover (A) and the sealing cap (B)
must be fitted to the additional handle (8).
- 19 -
29.11.2016 08:51:45 29.11.2016 08:51:45