Milwaukee M12 FUEL Manuel De L'utilisateur page 5

SYMBOLOGY
Volts
Direct Current
Rated Revolutions per Minute (RPM)
UL Listing for Canada and U.S.
C US
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always lock the trigger or remove
WARNING
the battery pack any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Only use accessories with Maximum Safe Operat-
ing Speed rated at least equal to the maximum
speed marked on the power tool. This speed is
based on the strength of the accessory, allow-
ing for a reasonable measure of safety. It is not
meant to imply a best or most efficient operating
speed. Do not exceed the Maximum Safe Operat-
ing Speed.
Do not touch the accessories with bare hands
immediately after drilling or buffing; they may
be hot and could burn skin.
Accessories
Drilling and buffing accessories should be protected
from:
• wetness and extreme humidity
• any type of solvent
• extreme changes in temperature
• dropping and bumping
Points, cones and plugs should be stored:
• in an organized way so points, cones, or plugs can
be removed without disturbing or damaging other
points, cones, or plugs
• with their safety information
Points, cones and plugs should NOT be dropped,
rolled or bumped.
Discard points, cones, or plugs that have been
dropped, rolled, bumped, subjected to extreme
changes in temperature, or come into contact with
solvents or wetness.
Installing Drill Bits into Collet
A 7/16" hex adapter is required to use a drilling bit.
1. Remove the battery pack.
2. To attach an accessory, pull the collet out and
hold.
3. Press the 7/16" hex adapter into the collet and
release the collet to lock it in place.
4. To remove the accessory, pull the collet out and
hold.
5. Pull out the 7/16" hex adapter and remove the
accessory. Release the collet.
Installing the Buffing Wheel
1. Remove the battery pack.
2. Install one of the nuts provided onto the threaded
end of the coupler and tighten the nut securely
with a 9/16" open end wrench.
3. Insert the buffing wheel.
4. Insert the washer.
Collet
5. Install and tighten the second nut securely with a
9/16" open end wrench.
NOTE: Use a 7/16" open end wrench to hold the
coupler to assist in tightening the nut.
6. Reverse the procedure when removing the ac-
cessory.
To reduce the risk of injury, always
WARNING
securely tighten the accessory to
the tire buffer and clean mandrels before insert-
ing them into the collet. Otherwise the high-speed
rotation of the tool could force the accessory to
fly out of the collet.
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool ON. The Fuel Gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1 light
on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the tool will not run. Charge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash and the tool will not run. Allow the battery
to cool down.
Using the Mode Selector
The mode selector button is used to adjust
the rotation speed (RPM) for the applica-
tion.
To select the mode:
Push the mode selector forward to select
buffing mode. This application is used
inside the inner liner inside of the tire.
Push the mode selector button down-
ward to select drilling
application is used on inside and outside
of the tire.
Mode Drilling Mode
RPM 0-1200
5
Buffing Wheel
Coupler
mode. This
Buffing Mode
0-2500
Nuts
Washer