Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4. Open the hydraulic shut-off valve located on the hydraulic
pressure hose. The handle should be in line with the
hose.
5. Open the bleed valve by rotating the bleed valve handle
fully counterclockwise.
6. Start the engine or turn on the electric motor.
a.
To start the gas
engine,
•
move the fuel valve
lever to the open
position,
•
move the throttle
lever to its middle
point,
•
move the choke lever
to the closed position
for a cold engine or
to the open position
for a warm engine,
•
turn the engine switch to the ON position, and
•
pull the starter rope briskly until the engine starts.
b.
To start the electric motor, move the ON/OFF switch to
the ON position.
7. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and solvent flows freely from the bleed
hose.
8. Allow the sprayer to run for 15–30 seconds to flush the
test fluid out through the bleed hose and into the waste
container.
9. Turn off the sprayer.
a.
To turn off the gas engine,
•
set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
•
move the throttle lever to the slow position, and
•
turn the engine switch to the OFF position.
b.
To turn off the electric motor,
•
set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
•
move the ON/OFF switch to the OFF position.
Preparing to Paint
Before painting, it is important to make sure that the fluid in the
system is compatible with the paint that is going to be used.
NOTE: Incompatible fluids and paint may cause the
valves to become stuck closed, which would
require disassembly and cleaning of the
sprayer's fluid section.
IMPORTaNT: always keep the trigger lock on the spray gun
in the locked position while preparing the system.
1. Place the siphon hose into a container of the appropriate
solvent.
NOTE: If you are spraying a water-based latex, flush with
warm, clean water. If you are using any other
material, check with the material manufacturer for
a compatible solvent.
2. Place the bleed hose into a metal waste container.
3. Set the pressure to minimum by turning the pressure
control knob fully counterclockwise.
4. Open the hydraulic shut-off valve located on the hydraulic
pressure hose. The handle should be in line with the
hose.
5. Open the bleed valve by rotating the bleed valve handle
fully counterclockwise.
© Titan Tool Inc. All rights reserved.
Choke Lever
Throttle
Lever
Engine
Switch
Fuel Valve
Starter Rope
Lever
6. Start the engine or turn on the electric motor.
a.
To start the gas engine,
•
move the fuel valve lever to the open position,
•
move the throttle lever to its middle point,
•
move the choke lever to the closed position for a cold
engine or to the open position for a warm engine,
•
turn the engine switch to the ON position, and
•
pull the starter rope briskly until the engine starts.
b.
To start the electric motor, move the ON/OFF switch to
the ON position.
7. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and solvent flows freely from the bleed
hose.
8. Allow the sprayer to run for 15–30 seconds to flush the
test fluid out through the bleed hose and into the waste
container.
9. Turn off the sprayer.
a.
To turn off the gas engine,
•
set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
•
move the throttle lever to the slow position, and
•
turn the engine switch to the OFF position.
b.
To turn off the electric motor,
•
set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
•
move the ON/OFF switch to the OFF position.
NOTE: Make sure that the spray gun does not have a tip
or tip guard installed.
10. Close the bleed valve by rotating the bleed valve handle
fully clockwise.
11. Start the engine or turn on the electric motor.
12. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure.
13. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
14. Trigger the gun into the metal waste container until the old
solvent is gone and fresh solvent is coming out of the gun.
15. Lock the gun by turning the gun trigger
lock to the locked position.
16. Set down the gun and increase the
pressure by turning the pressure control
knob slowly clockwise.
17. Check the entire system for leaks. If
leaks occur, follow the "Pressure Relief
Procedure" in this manual before
tightening any fittings or hoses.
18. Follow the "Pressure Relief Procedure" in this manual
before changing from solvent to paint.
Be sure to follow the pressure relief procedure
when shutting down the sprayer for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray tips, or
preparing for cleanup.
7
Trigger lock in
locked position.
English
Publicité
Chapitres
Table des Matières
Dépannage
