Table Des Matières; Specifications - Titan PowrTwin 12000 Plus Notice D'utilisation

Table of contents
Safety Information .................................................................... 2
Grounding Instructions ........................................................ 3
Gasoline Engine Safety ....................................................... 3
Français............................................................................. 28
Español ............................................................................. 54
Specifications ........................................................................... 4
Introduction ............................................................................... 5
Operation ................................................................................... 5
Fueling................................................................................. 5
Setup ................................................................................... 6
Preparing to Paint................................................................ 7
Painting ............................................................................... 8
Pressure Relief Procedure .................................................. 8
cleanup ..................................................................................... 9
Cleaning a Clogged Tip ....................................................... 9
Maintenance ............................................................................ 10
Daily Maintenance ............................................................. 10
Maintaining the Filter Assembly ........................................ 10
Maintaining the Hydraulic System ..................................... 11
Maintaining the Fluid Section ............................................ 11
Basic Engine Maintenance (gas engine) ........................... 11
Replacing the Motor Brushes (electric motor) ................... 12
Troubleshooting ..................................................................... 13
Airless Gun ........................................................................ 13
Fluid Section...................................................................... 13
Hydraulic Motor ................................................................. 14
Spray Patterns................................................................... 15
Parts Lists and Service Instructions .............................. 16-29
Main Assembly .................................................................. 16
Bleed Hose Assembly with Valve ...................................... 16
Cart Assembly ................................................................... 17
Hydraulic System .............................................................. 18
DC- Electric Convertokit.................................................. 19
Belt Guard Assembly......................................................... 20
Filter Assembly .................................................................. 21
Gas Convertokit................................................................. 22
Bleed Valve Assembly....................................................... 22
Siphon Hose Assembly ..................................................... 23
Hydraulic Motor ................................................................. 24
Fluid Section...................................................................... 26
Gun Manifold Assemblies (optional).................................. 28
SAE O-Ring Fitting Installation .......................................... 29
accessories and Service Kits ............................................... 29
Airless Tip Selection .......................................................... 29
Limited Warranty .................................................................... 88
English

Specifications

Gas Sprayer
Gallons per minute (GPM) ............. 3.15 (11.9 LPM)
Cycle rate per gallon...................... 38 (10.5 cycles/liter)
Maximum tip sizes ......................... 1 gun = .059"
Maximum pressure ........................ 3600 psi (24.8 MPa)
Power ......................................... Honda 270cc, 8.5 HP,
Fuel capacity ................................. 1.4 US gallons
Halogenated solvent compatible ... Yes
Weight ......................................... 182 lbs. (83 kg.)
Inlet paint filter ............................... 10 mesh "Rock Catcher"
Outlet paint filter ............................ 50 mesh, 18 in.
Pump inlet...................................... 1" NPT(F)
Pump outlet ................................... 1/2" NPT(F) to paint filter
Paint filter hose connections.......... 1/4" NPS(M)
Dimensions .................................... 46" L (116.8 cm) x
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, PTFE, thiokol
impregnated leather, ultra high molecular weight polyethylene.
Electric Sprayer (with optional convertokit)
Gallons per minute (GPM) ............. 1.25 (4.7 LPM)
Cycle rate per gallon...................... 40 (10.5 cycles/liter)
Maximum tip sizes ......................... 1 gun = .036"
Maximum pressure ........................ 3600 psi (24.8 MPa)
Power ......................................... 2 HP DC Motor, 115V 15.5A,
Halogenated solvent compatible ... Yes
Weight ......................................... 188 lbs. (85.3 kg.)
Inlet paint filter ............................... 10 mesh "Rock Catcher"
Outlet paint filter ............................ 50 mesh, 18 in.
Pump inlet...................................... 1" NPT(F)
Pump outlet ................................... 1/2" NPT(F) to paint filter
Paint filter hose connections.......... 1/4" NPS(M)
Dimensions .................................... 46" L (116.8 cm) x
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, PTFE, thiokol
impregnated leather, ultra high molecular weight polyethylene.
4
2 guns = .040"
3 guns = .034"
4 guns = .030"
5 guns = .026"
6 guns = .024"
4-stroke, single cylinder,
overhead valve engine w/oil
alert
(approx. 2.5 hours run time)
2
3/8" NPT(F) (plugged)
3/8" NPS(M)
27" W (68.6 cm) x
34" H (86.6 cm)
2 guns = .033"
3 guns = .023"
4 guns = .019"
overload protected
2
3/8" NPT(F) (plugged)
3/8" NPS(M)
27" W (68.6 cm) x
34" H (86.6 cm)
© Titan Tool Inc. All rights reserved.