AEG KRC 4355 CD Mode D'emploi page 38

English
38
Playing CDs
NOTE:
Observe the following operation for the replay of CD' s in
the MP3 format! The device is not MP3 capable. The CD
will however start to turn, but the sound cannot be repro-
duced.
This is how you play a CD
1. Select the CD mode with the FUNCTION button (13/27).
The following will appear in the display "- -".
2. Press the OPEN/CLOSE button (9/26) to open the CD
tray.
3. Place the CD into the CD tray with the label side up.
Press the OPEN/CLOSE button once more to close the
CD tray again.
4. After a few seconds the total number of songs/tracks is
shown in the display.
5. Press the PLAY/PAUSE (
play from the first title. The current title number and the
notification " " are shown on the display.
6. In order to remove a CD, please press the STOP ( )
button (8/34), open the CD compartment and lift the CD
out carefully.
Always keep the CD tray closed.
NOTE:
• If a disc is inserted the wrong way around, respectively if
no disc is inserted, then the message "- -" will blink and
"NO" appears on the display.
• Playback of CDs produced by the user cannot be
guaranteed due to the large variety of software and CD
media available.
• Please note:
There are many burning and compression methods,
as well as quality differences between CDs and burned
CDs.
The music industry furthermore does not observe any
fixed standards (copyright protection).
For these reasons, in rare cases there may be problems
when playing CDs. This is not a malfunction of the
device.
Description of the CD buttons
PLAY/PAUSE ( ) (10/24)
You can briefly interrupt and resume playback using this but-
ton. The symbol " " will flash on the display. Pressing again
continues playback.
F.FWD / REW ( / / / ) (6/7/33)
With F.FWD ( / ) you can jump to the next or previous
track etc.
) button (10/24). The CD will
• If the button is kept pressed down, the machine starts to
search through the tracks.
The REW ( / ) button can be used as follows:
Press once = This starts the current track again from the
beginning.
Press twice = This jumps back to the previous track.
Press three times = This plays the song before etc. If the but-
ton is kept pressed down, the machine
starts to search through the tracks.
STOP ( ) (8/34)
The CD stops.
REPEAT (5/23)
With a CD currently playing:
Press once = (the emits a fixed light) the current
track is repeated continuously.
Press twice = (the ALL
CD is played continuously.
Press three times = all functions are cancelled. The normal
play mode is resumed.
Programmed Play
This can be used to program any desired sequence of tracks.
1. Press the STOP ( ) button (8/34).
2. Press the MEM/PROG button (4/21). The memory
location "01" and the notification "PROG" will blink
in the display. Use the F.FWD / REW ( / / / )
buttons (6/7/33) to select the desired track and then press
the MEM/PROG button again. The display changes to
memory slot 02.
3. Select the next track with the F.FWD / REW ( / /
/ ) buttons and press the MEM/PROG button again.
Repeat the procedure until all the desired tracks are
selected.
NOTE:
If the storage capacity of the titles to be programmed
has been reached, all the programmed titles will be
shown in sequence.
4. Press the PLAY/PAUSE (
starts. The current title number, the notification " " and
"PROG" will be shown in the display.
5. Press once the STOP ( ) button to stop the playback
while retaining the program.
6. To play the programme back again, press the PLAY/
PAUSE ( ) button.
7. To delete the program, press the STOP ( ) button twice.
The PROG control lamp goes out.
The device stops automatically after all programmed titles
have been played. The indication PROG goes out and the
programmed sequence is deleted from the memory.
emits a fixed light) the whole
) button (10/24). The playback