DeWalt DCF888 Traduction De La Notice D'instructions Originale page 37

• Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recycling facility.
OPERATION

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury. Exception—Tool Connect™
functions and mode adjustments require battery to
be installed.
NOTICE: Always check the tool configuration prior to
use. If you are unsure of the current configuration, press
the mode button 11 (Fig. D) to set the tool to the Home
setting as described on the label and this manual.
Proper Hand Position (Fig. E)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle 10 .
Using the Tool
Your impact tool generates the following maximum torque:
cat #
DCF888
nOTE: Tool Connect™ custom speed settings will affect the
maximum torque output of the tool. Speeds lower than the
Home setting generally result in lower maximum torque.

CAUTION: Ensure fastener and/or system will withstand
the level of torque generated by the tool. Excessive torque
may cause breakage and possible personal injury.
1. Place the accessory into the chuck. Keep the tool pointed
straight at the workpiece.
2. Press switch to start operation. Release the switch to stop
operation. Always check torque with a torque wrench, as
the fastening torque is affected by many factors including
the following:
- Voltage: Low voltage, due to a nearly discharged
battery, will reduce fastening torque.
socket size: Failure to use the correct socket size will
-
cause a reduction in fastening torque.
- Bolt size: Larger bolt diameters generally require
higher fastening torque. Fastening torque will also vary
according to length, grade, and torque coefficient.
- Bolt: Ensure that all threads are free of rust and other
debris to allow proper fastening torque.
-
-
MAINTENANCE
Your D
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning


nm
205
Optional Accessories


Consult your dealer for further information on the
appropriate accessories.
Material: The type of material and surface finish of the
material will affect fastening torque.
Fastening Time: Longer fasten ing time results in
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners to
be overstressed, stripped or damaged.
WALT power tool has been designed to operate
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury. Exception—Tool Connect™
functions and mode adjustments require battery to
be installed.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessories prior to use to ensure that they contain
no cracks.
EnGLIsh
WALT recommended
e
35