DeWalt DCF888 Traduction De La Notice D'instructions Originale page 36

EnGLIsh
Worklights (Fig. A)

CAUTION: Do not stare into worklight. Serious eye
injury could result.
The three worklights 7 located around the chuck collar
activated when the trigger switch is depressed. In the factory
default mode, when the trigger is released, the worklight will
stay illuminated for up to 20 seconds. If the trigger switch
remains depressed, the worklights will remain on. These settings
can be customized using the Tool Connect™ app. Refer to
Mode Selector.
nOTE: The worklights are for lighting the immediate work
surface and are not intended to be used as a flashlight.
Mode Selector (Fig. A, D)

WARNING: To reduce the risk of injury, remove
accessories from the tool chuck before using the
mode selector.
Your tool is equipped with a mode selector that allows modes 1,
2, and 3 to be customized using the Tool Connect™ app. Home
settings are active when the home indicator
Table 1 for customizable features.
Once configured, pressing the mode selector button
on the foot of the tool will cycle through the modes
you are unsure of the current configuration, press the mode
selector button 11 to set the tool to the Home setting (home
indicator 15 is lit).
D WALT Tool Connect™ (Fig. D)
e

WARNING: To reduce the risk of injury, remove accessories
from the tool chuck before any Tool Connect™ interaction.
NOTICE: Always check the tool configuration prior to
use. If you are unsure of the current configuration, press
the mode selector button
Home setting as described on the label and this manual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology. (To
see if your mobile device is compatible, visit: http://www.
bluetooth.com/Pages/Bluetooth-Smart-Devices-List.aspx)
D WALT Tool Connect™ is an optional application for your
e
smart device (such as a smart phone or tablet) that connects
the device to your tool to allow you to configure specific tool
functions. Refer to Mode Selector.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
TaBLE 1
Customizable Features
Worklight brightness
Worklight delay off
Maximum speed (RPM)
Precision Drive hesitation (seconds)
34
3 are
15 is lit. Refer to
11
14 . If
11 (Fig. D) to set the tool to the
Home Mode 1
High
20 secs 20 secs
3250
Disabled
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D WALT Tool Connect™ application at:
e
• Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from the Tool.
• Follow the instructions in the app to create your Tool
Connect™ account.
• On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to the app.
• To connect your tool with the D
app, at the appropriate screen, press the mode selector
button 11 for 3–5 seconds, then wait for the tool to
connect. The tool can only be connected to one Tool
Connect™ account at a time.
• Once the tool has been connected, you can confirm that
you would like to register the product.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
D WALT service center. Do not attempt to replace the coin cell
e
battery yourself.

WARNING: Danger of explosion if battery is
incorrectly replaced.

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead
to death.
• Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away from children.
• If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
• If the coin cell battery contents come into contact
with the skin, immediately wash area with mild soap
and water. If coin cell battery liquid gets into the eye,
rinse water over the open eye for 15 minutes or until
irritation ceases. If medical attention is needed, the
battery electrolyte is composed of an organic solvent
and lithium salts.
Factory Presets
Mode 2
High High
20 secs
1000 2800
1 Disabled
WALT Tool Connect™
e
Mode 3 Customizable Range
High OFF–High
20 secs 0–20 minutes
3250 1000–3250
Disabled 0–1