Intended Use; Technical Data; Before Starting The Equipment - EINHELL GE-LC 36/35 Li Traduction Du Mode D'emploi D'origine

3. Intended use

The chainsaw is intended for felling small trees
and for cutting trunks, branches, wooden beams,
boards etc. and can be used for cross cuts and
longitudinal cuts. It is not suitable for cutting any
materials other than wood.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............. 36 V
No load speed: ........................... 8200 rpm (min
Bar length:....................................14 in. (35.6 cm)
Cutting thickness max.: ................... 13 in. (33 cm)
Chain pitch: ......................... ⅜ (9.5 mm), 52 teeth
Chain Gauge: ..........................0.043 in. (1.1 mm)
Saw chain: ...........Oregon
Bar: ..................................Oregon
Cutting speed at rated rpm: ......590.6 ips (15 m/s)
Oil tank capacity: ...................... 3.88 fl oz (115 ml)
Weight: ........................................... 8.81 lbs (4 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
Anl_GE_LC_36_35_Li_SPK7_USA.indb 15 Anl_GE_LC_36_35_Li_SPK7_USA.indb 15
EN
(2x 18V)
)
-1
90PX052X / 52 Teeth
®
144MLEA041
®
- 15 -

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
Danger! Do not fi t the battery until the chainsaw
has been fully assembled and the chain tension
has been set. Always wear protective gloves
when working on the chainsaw to protect yourself
against injury.
5.1 Assembly of the bar and the saw chain
•
Carefully unpack all parts and check that they
are complete (Fig. 2-3).
•
Undo the fixing screw of the chain wheel
cover (Fig. 4).
•
Take off the chain wheel cover (Fig. 5).
•
Lay the chain as shown in the groove which
runs around the bar (Fig. 6/See arrow).
•
Insert the bar and chain as shown in the
mounting in the chainsaw. At the same time
guide the chain around the chain sprocket
wheel (Fig. 7 and 8/Item 12).
•
Attach the chain wheel cover and secure it
with the fixing screw (Fig. 9). Important! Do
not fully tighten the fastening screw until after
you have adjusted the chain tension (see
section 5.2).
5.2 Tensioning the saw chain
Warning! Always pull out the battery before
performing any checks or adjustments. Always
wear protective gloves when working on the
chainsaw to protect yourself against injury.
•
Undo the fixing screw of the chain wheel
cover a few turns (Fig. 4).
•
Adjust the chain tension with the chain
tensioning screw (Fig. 10/Item 10). Turning
the screw clockwise increases the chain
tension, turning it counter-clockwise
decreases the chain tension. The chain
tension is correct when the chain can be lifted
by about 0.11 in. at the center of the bar (Fig.
11).
•
Tighten the fixing screw of the chain wheel
cover (Fig. 9).
Danger! All the chain links must lie properly in the
guide groove of the bar.
03.06.2019 15:34:49 03.06.2019 15:34:49