EINHELL GE-LC 36/35 Li Traduction Du Mode D'emploi D'origine page 13

Chain saw safety warnings
1. Keep all parts of the body away from
the saw chain when the chain saw is
operating. Before you start the chain
saw, make sure the saw chain is not
contacting anything. A moment of
inattention while operating chain saws may
cause entanglement of your clothing or body
with the saw chain.
2. Always hold the chain saw with your
right hand on the rear handle and your
left hand on the front handle. Holding the
chain saw with a reversed hand confi guration
increases the risk of personal injury and
should never be done.
3. Hold the power tool by insulated gripping
surfaces only, because the saw chain
may contact hidden wiring. Saw chains
contacting a "live" wire may make exposed
metal parts of the power tool "live" and could
give the operator an electric shock.
4. Wear safety glasses and hearing
protection. Further protective equipment
for head, hands, legs and feet is
recommended. Adequate protective clothing
will reduce personal injury by fl ying debris or
accidental contact with the saw chain.
5. Do not operate a chain saw in a tree.
Operation of a chain saw while up in a tree
may result in personal injury.
6. Always keep proper footing and operate
the chain saw only when standing on
fi xed, secure and level surface. Slippery or
unstable surfaces such as ladders may cause
a loss of balance or control of the chain saw.
7. When cutting a limb that is under tension
be alert for spring back. When the tension
in the wood fi bers is released the spring
loaded limb may strike the operator and/or
throw the chain saw out of control.
8. Use extreme caution when cutting brush
and saplings. The slender material may
catch the saw chain and be whipped toward
you or pull you off balance.
9. Carry the chain saw by the front handle
with the chain saw switched off and
away from your body. When transporting
or storing the chain saw always apply
the guide bar cover. Proper handling of
the chain saw will reduce the likelihood of
accidental contact with the moving saw chain.
10. Follow instructions for lubricating, chain
tensioning and changing accessories.
Improperly tensioned or lubricated chain
may either break or increase the chance for
Anl_GE_LC_36_35_Li_SPK7_USA.indb 13 Anl_GE_LC_36_35_Li_SPK7_USA.indb 13
EN
kickback.
11. Keep handles dry, clean, and free from oil
and grease. Greasy, oily handles are slippery
causing loss of control.
12. Cut wood only. Do not use chain saw for
purposes not intended. For example: do
not use chain saw for cutting plastic,
masonry or non-wood building materials.
Use of the chain saw for operations diff erent
than intended could result in a hazardous
situation.
Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden
reverse reaction, kicking the guide bar up and
back towards the operator.
Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back towards
the operator.
Either of these reactions may cause you to lose
control of the saw which could result in serious
personal injury. Do not rely exclusively upon the
safety devices built into your saw. As a chain saw
user, you should take several steps to keep your
cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below:
•
Maintain a firm grip, with thumbs and
fingers encircling the chain saw handles,
with both hands on the saw and position
your body and arm to allow you to
resist kickback forces. Kickback forces
can be controlled by the operator, if proper
precautions are taken. Do not let go of the
chain saw.
•
Do not overreach and do not cut above
shoulder height. This helps prevent
unintended tip contact and enables better
control of the chain saw in unexpected
situations.
•
Only use replacement bars and chains
specified by the manufacturer. Incorrect
replacement bars and chains may cause
chain breakage and/or kickback.
•
Follow the manufacturer's sharpening
and maintenance instructions for the saw
chain. Decreasing the depth gauge height
can lead to increased kickback.
- 13 -
03.06.2019 15:34:48 03.06.2019 15:34:48