Maintenance - EINHELL RT-TS 1221 Mode D'emploi D'origine

Masquer les pouces Voir aussi pour RT-TS 1221:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 20
Anleitung_RT-TS 1221_SPK1:_
GB
8.3 Setting the angle (Fig. 10)
Undo the fixing handle (15).
Turn the locking screw (16) to set the blade (4) to
the required angle value (see scale (13)).
Re-tighten the fixing handle (15).
8.4. Cross stop (Figure 9)
Slide the cross stop (14) into the groove (a) of
the table.
Slacken the knurled screw (c).
Turn the cross stop (14) until the arrow points to
the angle required.
Retighten the knurled screw (c).
When cutting large parts of workpieces you can
use the stop rail (25) from the parallel stop (7) to
extend the length of the cross stop (14).
8.5 Table width extension (21) (Fig. 1/9/10)
Important!
The table width extension should be pulled out for
wide pieces of wood.
Slacken the knurled screws (e)
Pull out the table width extension (21)
Swing out the support foot (22)
Retighten the knurled screws (e)
9. Sawing operations
After each new adjustment it is advisable to
carry out a trial cut in order to check the set
dimensions.
After switching on the saw, wait for the blade to
reach its maximum speed of rotation before
commencing with the cut.
Secure long workpieces against falling off at the
end of the cut (e.g. with a roller stand etc.)
Take extra care when starting the cut!
9.1 Cutting narrow workpieces
(width less than 120 mm) (Fig. 12)
Adjust the parallel stop (7) to the width of
workpiece you require.
Feed in the workpiece with two hands. Always
use the push stick (3) in the area of the saw
blade (4).
(A push stick is supplied with the saw!)
Always push the workpiece through to the end of
the splitter (5).
Caution! With short workpieces, use the push
stick from the beginning.
18
06.12.2010
8:45 Uhr
Seite 18
9.2 Cutting extremely narrow workpieces
(width less than 30 mm) (Fig. 13)
Adjust the parallel stop (7) to the width of
workpiece you require.
Use the push block (d) to press the workpiece
against the stop rail (25) and push the workpiece
with the push stick (3) through to the end of the
splitter (5).
There is no push block supplied with the
saw!
(Available from your specialist dealer)
9.3 Cross cuts (Fig. 9)
Slide the cross stop (14) into the groove (a) in
the table and adjust to the required angle (see
8.4).
Use the stop rail (25).
Press the workpiece firmly against the cross stop
(14).
Switch on the saw.
Push the cross stop (14) and the workpiece
toward the blade in order to make the cut.
Important:
Always hold the guided part of the
workpiece. Never hold the part which is to be
cut off.
Push the cross stop (14) forward until the
workpiece is cut all the way through.
Switch off the saw again.

10. Maintenance

Important. Always pull out the power plug before
carrying out any maintenance or conversion
work on the bench type circular saw.
Remove dust and dirt regularly from the
machine. Cleaning is best done with compressed
air or a rag.
Never use caustic agents to clean plastic parts.
11. Orders for replacement parts
Please quote the following information on all orders
for replacement parts:
Type of product
Article number of the product
ID number of the product
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

43.407.41

Table des Matières