Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL RG-EM 1233 Mode D'emploi D'origine

Anleitung_RG_EM_1233_SPK1:_
GB

8. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or by similarly trained personnel to
avoid danger.
9. Cleaning, maintenance and ordering
of spare parts
Always pull out the power plug before starting any
cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
down with compressed air at low pressure.
We recommend that you clean the equipment
immediately after you use it.
Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the
plastic parts in the equipment. Ensure that no
water can get into the interior of the equipment.
9.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked by a qualified electrician.
Important! The carbon brushes should not be
replaced by anyone but a qualified electrician.
9.3 Maintenance
Worn out or damaged blades, blade mounts, and
bolts should be replaced as a set by an
authorized professional in order to keep the
equipment in balance.
Do not clean the lawn mower with running water,
particularly with high-pressure water. Ensure that
all mounting components (i.e. screws, bolts, nuts
etc.) are always tightened so that the equipment
can be safely operated at all times.
Frequently check the grass catch assembly for
signs of wear.
Replace excessively worn or damaged parts
immediately.
Store your lawn mower in a dry room.
In order to ensure that you enjoy the equipment
for many years to come, all screwed parts, as well
as the wheels and axles, should be cleaned and
lubricated.
Keeping your lawn mower in good condition not
only ensures a long lifespan and high
performance, but also enables the equipment to
22
21.07.2011 10:28 Uhr Seite 22
thoroughly cut your grass with minimal effort. For
best results, clean the lawn mower with a brush
or rag. Do not use any solvents or water to
remove dirt.
The blade is subjected to more wear and tear
than any other component. Therefore, routinely
check the condition of the blade and make sure
that it is tightly fastened. If the blade is completely
worn out, it must be immediately replaced or
ground sharp again. An excessively vibrating
mower means that the blade is not properly
balanced or has become deformed from striking
an object. In this case, the blade must be
repaired or replaced.
There are no parts inside the equipment which
require additional maintenance.
9.4 Replacing the blade
For safety reasons, we recommend having the blade
replaced by an authorized professional. Important!
Wear work gloves! Only replace the blade with a
genuine Einhell replacement blade, as this will ensure
top performance and safety under all conditions.
Carry out the following steps to change the blade:
Undo the fastening screw (see Fig. 7).
Remove the blade and replace with a new one.
When fitting the blade, make sure it is installed in
the right direction. The blade's air vanes must
project into the motor compartment (see Fig. 7).
The dome mounts must be aligned with the
punch holes in the blade (see Fig. 8).
Then retighten the fastening screw with a wrench.
The tightening torque should be approx. 25 Nm.
At the end of the season, perform a general
inspection of the lawn mower and remove any grass
and dirt which may have accumulated. At the start of
each season, ensure that you check the condition of
the blade. If repairs are necessary, please contact our
customer service center. Use only genuine spare
parts.
9.5 Ordering replacement parts:
Please provide the following information on all orders
for spare parts:
Model/type of the equipment
Article number of the equipment
ID number of the equipment
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
Spare blade art. no.: 34.054.60