Further Safety Instructions For All Saws - Hitachi CM 5SB Instructions De Sécurité Et Mode D'emploi

6. NEVER use a power tool for applications other
than those specified.
NEVER use a power tool for applications other than
those specified in the Instruction Manual.
7. Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool.
NEVER allow the tool to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
8. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
9. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
10. Blades and accessories must be securely mounted
to the tool.
Prevent potential injuries to youself or others.
Blades, cutting implements and accessories which
have been mounted to the tool should be secure
and tight.
11. Keep motor air vent clean.
The tool's motor air vent must be kept clean so
that air can freely flow at all times. Check for dust
build-up frequently.
12. Operate power tools at the rated voltage.
Operate the power tool at voltages specified on its
nameplate.
If using the power tool at a higher voltage than
the rated voltage, it will result in abnormally fast
motor revolution and may damage the unit and
the motor may burn out.
13. NEVER use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange
for repairs by a Hitachi authorized service center.
14. NEVER leave tool running unattended. Turn power
off.
Don't leave tool until it comes to a complete stop.
15. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
16. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly
dampened with soapy water and dry thoroughly.
17. ALWAYS wear eye protection that meets the
requirement of the latest revision of
ANSI Standard Z87.1.
18. ALWAYS wear a mask or respirator to protect
yourself from dust or potentially harmful particles
generated during the operation.
19. Do NOT use any cutting tool other than a diamond
wheel.
Use the diamond wheel specified in this manual.
20. Don't use it for cutting of metallic materials.
Diamond wheel may be broken or its service life
may be remarkably reduced when it is used for
cutting of metallic materials. Be sure not to use
the wheel for cutting of metals.
21. Do not start the cutter while the diamond wheel
is in contact with the material.
22. Keep the motor interior free of water.
23. Prior to use, be sure to check the diamond wheel
in such details as crack, broken part, bent part and
the like. Don't use a diamond wheel if any of the
above defect is found on the wheel. Also confirm
that no abnormality exists by actual test running.
24. Proceed with cutting operation when full speed
has been reached.
25. Do NOT apply excessive force.
26. When cutting concrete, tile, or stone, the
maximum cutting depth should be held to within
13/64"(5 mm).
27. Never lay down the cutter while the diamond
wheel is revolving.
Also, do not stop the cutter with the diamond wheel
forcibly depressed against the material.
28. Exercise care to position the cutter at a safe, stable
spot when cutting.
29. Take good care of the power tool and keep it clean.
30. Definitions for symbols used on this tool
V ............... volts
Hz ............. hertz
A ............... amperes
n .............. no load speed
o
W .............. watt
............. Class II Construction
---/min ...... revolutions per minute
FURTHER SAFETY INSTRUCTIONS FOR
ALL SAWS
DANGER!
a) Keep hands away from cutting area and do not
reach underneath the workpiece. Contact with the
wheel will result in injury.
b) Adjust the cutting depth to the thickness of the
workpiece.
c) Never hold piece being cut in your hands or across
your leg. Secure the workpiece to a stable
platform.
English
5