Publicité
Les langues disponibles
Les langues disponibles
• KEEP ALL POWER CORDS AND CABLES AWAY FROM CUTTING AREA. POWER
CORDS OR CABLES MAY BE HIDDEN IN HEDGES OR BUSHES AND CAN BE
ACCIDENTALLY CUT BY THE BLADE.
• DO NOT TRY TO GRASP OR REMOVE TRIMMINGS WHEN THE PRODUCT IS
RUNNING. ONLY REMOVE TRIMMINGS WHEN THE PRODUCT IS SWITCHED OFF
AND DISCONNECTED FROM POWER SOURCE.
• NEVER HOLD THE PRODUCT BY THE GUARD.
• ALWAYS BE SURE OF A SAFE AND SECURE OPERATING POSITION, WHILST
USING THE PRODUCT.
• NEVER USE THE PRODUCT STANDING ON STEPS OR A LADDER. DO NOT
WORK OVER SHOULD HEIGHT.
2.10 OPERATION SAFETY WARNINGS
• CHECK THE PRODUCT, ITS POWER PLUG AND WIRE AS WELL AS
ACCESSORIES FOR DAMAGE BEFORE EACH USE. DO NOT USE THE PRODUCT IF
IT IS DAMAGED OR SHOWS WEAR.
• DOUBLE CHECK THAT THE ACCESSORIES AND ATTACHMENTS ARE PROPERLY
FIXED.
• ALWAYS HOLD THE PRODUCT ON ITS HANDLE. KEEP THE HANDLE DRY TO
ENSURE SAFE SUPPORT.
• ENSURE THAT THE AIR VENTS ARE ALWAYS UNOBSTRUCTED AND CLEAR.
CLEAN THEM IF NECESSARY WITH A SOFT BRUSH. BLOCKED AIR VENTS MAY
LEAD TO OVERHEATING AND DAMAGE THE PRODUCT.
• SWITCH THE PRODUCT OFF IMMEDIATELY IF YOU ARE DISTURBED WHILE
WORKING BY OTHER PEOPLE ENTERING THE WORKING AREA. ALWAYS LET
THE PRODUCT COME TO COMPLETE STOP BEFORE PUTTING IT DOWN.
• DO NOT OVERWORK YOURSELF. TAKE REGULAR BREAKS TO ENSURE YOU
CAN CONCENTRATE ON THE WORK AND HAVE FULL CONTROL OVER THE
PRODUCT.
• BEFORE SWITCHING THE PRODUCT ON, CHECK WHETHER IT HAS BEEN
ASSEMBLED CORRECTLY AND ALL THE MOVING PARTS ARE RUNNING
SMOOTHLY.
• WARNING: IN SOME COUNTRIES REGULATIONS DEFINE AT WHAT TIME OF
THE DAY AND ON WHAT SPECIAL DAYS PRODUCTS ARE ALLOWED TO BE USED
AND WHAT RESTRICTIONS APPLY! ASK YOUR COMMUNITY FOR DETAILED
INFORMATION AND OBSERVE THE REGULATIONS IN ORDER TO PRESERVE
A PEACEFUL NEIGHBOURHOOD AND AVOID COMMITTING ADMINISTRATIVE
OFFENCES!
• ALWAYS ENSURE THE SAFETY GUARD SUPPLIED IS FITTED BEFORE USING
THE PRODUCT. NEVER ATTEMPT TO USE AN INCOMPLETE PRODUCT OR ONE
FITTED WITH AN UNAUTHORISED MODIFICATION.
• CHECK THE CUTTING DEVICE REGULARLY FOR DAMAGE, AND IF DAMAGED
REPAIR IMMEDIATELY.
• SWITCH THE PRODUCT OFF WHEN THE CUTTING DEVICE IS BLOCKED.
DISCONNECT THE POWER SOURCE AND REMOVE THE BLOCKAGE. INSPECT THE
CUTTING DEVICE FOR DAMAGE BEFORE USING THE PRODUCT AGAIN.
• DO NOT OVERLOAD YOUR TOOL.
• HAVE THE PRODUCT CHECKED BY A QUALIFIED PROFESSIONAL AND
REPAIRED, IF NECESSARY, BEFORE YOU OPERATE IT AGAIN.
• OPERATING HOURS - ONLY OPERATE THE PRODUCT AT REASONABLE HOURS
- NOT EARLY IN THE MORNING, LATE AT NIGHT OR ON WEEKENDS/PUBLIC
HOLIDAYS WHEN PEOPLE MIGHT BE DISTURBED. INFORM YOURSELF ABOUT
LOCAL RESTRICTIONS
• AVOID USING THE PRODUCT IN BAD WEATHER CONDITIONS, ESPECIALLY
WHEN THERE IS A RISK OF LIGHTNING. DO NOT OPERATE THE PRODUCT IN
POOR LIGHTING. THE OPERATOR REQUIRES A CLEAR VIEW OF THE WORK AREA
TO IDENTIFY POTENTIAL HAZARDS.
• USE OF HEARING PROTECTION REDUCES THE ABILITY TO HEAR WARNINGS
(SHOUTS OR ALARMS). THE OPERATOR MUST PAY EXTRA ATTENTION TO WHAT
IS GOING ON IN THE WORK AREA. DO NOT GET DISTRACTED, AND ALWAYS
CONCENTRATE ON THE TASK.
• OPERATING SIMILAR TOOLS NEARBY INCREASES BOTH THE RISK OF
HEARING INJURY AND THE POTENTIAL FOR OTHER PERSONS TO ENTER YOUR
WORK AREA.
• WALK, NEVER RUN. KEEP ALL PARTS OF YOUR BODY AWAY FROM ANY
MOVING PART.
• NEVER RUN THE PRODUCT WITHOUT THE PROPER EQUIPMENT ATTACHED.
• DO NOT MODIFY THE PRODUCT IN ANY WAY OR USE PARTS AND
ACCESSORIES THAT ARE NOT RECOMMENDED BY THE MANUFACTURER.
181
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
Publicité
