Ryobi EWS-1266 Manuel D'utilisation page 9

GB
FR DE ES IT
INSTRUCTIONS FOR SAFE HANDLING
The maximum permissible system impedance:
Zmax for EWS-1266 is 0.245 Zref & Zmax for EWS-1366
is 0.252 Zref.
If in doubt, please verify with your local energy-utilitythat the
AC outlets in your area do not exceed theabobe values.
STANDARD ACCESSORIES
Saw blade, Parallel fence, Spanner.
APPLICATION
Sawing wood.
NOISE BUILD-UP
Noise (sound pressure level) in the workplace can exceed
85 dB. In this case, sound insulation and hearing protection
measures must be taken by the operator.
ASSEMBLY INSTRUCTIONS
BE SURE TO DISCONNECT THE TOOL FROM
T H E P O W E R S U P P LY B E F O R E AT TA C H I N G
OR REMOVING THE SAW BLADE. BE SURE THAT
THE TEETH OF THE SAW BLADE ARE POINTING
UPWARD AT THE FRONT OF THE TOOL.
ATTACHING AND REMOVING
THE BLADE (FIGURES 2, 3, 4, AND 5)
ATTACHING THE BLADE
1. Pressing the spindle lock button (1), turn the hex-head
bolt (2) with the spanner (3) until the spindle locks.
(Fig.2)
2. Loosen the hex-head bolt by turning the spanner
anticlockwise while pressing the spindle lock button.
(Fig.2)
3. Remove the hex-head bolt and the outer blade washer
(4). (Fig. 2)
4. Retract the lower guard (5) back with the lower guard
lever (6) as far as possible under the upper guard (7).
(Fig. 3)
5. Then, attach the saw blade (8) against the inner blade
washer (9) on the spindle. Then fit the outer blade
washer and the hex-head bolt. (Fig. 3 and 4)
6. Press the spindle lock button again, tighten the hex-
head bolt by turning the spanner clockwise while
pressing the spindle lock button. (Fig. 5)
EWS-1266&EWS-1366_24lgs manual_03_2009.12.04.indd Sec1:3 EWS-1266&EWS-1366_24lgs manual_03_2009.12.04.indd Sec1:3
NL PT DK SE FI NO
English
RU PL CZ HU RO LV
7. After tightening the hex-head bolt, release the spindle
lock button.
REMOVING THE BLADE
1. Pressing the spindle lock button, turn the hex-head
bolt with the spanner until the spindle locks.
2. Loosen the hex-head bolt by turning the spanner
anticlockwise while pressing the spindle lock button.
3. Remove the hex-head bolt and the outer blade
washer.
4. Retract the lower guard back as far as possible under
the upper guard, then remove the saw blade.
ADJUSTING THE RIVING KNIFE (FIG. 6)
WARNING!
Do not use saw blades the disk of which is
thicker, or the set of which is smaller, then the
thickness of the riving knife.
1. Ensure that the riving knife is adjusted so that (Fig. 6):
A. The distance between the riving knife (11) and the
toothed rim of the saw blade is under 5 mm.
B. The toothed rim does not extend more than 5 mm
beyond the lower edge of the riving knife.
2. The riving knife should always be used except when
making a plunging cut in the middle of a workpiece.
ADJUSTING THE DEPTH OF CUT (FIG. 7A, 7B,
8, 9)
1. To adjust the depth of cut, loosen the depth adjustment
knob (12). (Fig. 7A)
2. Slide the base plate (13) to the desired depth using
the depth adjustment lug (21) and retighten the knob
securely. (Fig. 7B)
3. The depth of cut (14) can be determined by the depth
scale (15) or by measuring the distance by which the
blade protrudes from the base plate. (Fig. 8 and 9)
ADJUSTING THE CUTTING ANGLE (FIG. 10A,
10B)
1. The cutting angle may be set to any position between
0° and 45°. (Fig. 10A)
2. Loosen the bevel adjustment knob (16) at the front of
the tool and move the base plate to the desired angle
using the bevel scale (17). (Fig.10B)
3. Once the angle has been set, be sure to retighten the
bevel adjustment knob firmly.
3
LT EE HR SI SK GR
12/4/09 1:57:51 PM 12/4/09 1:57:51 PM
TR