Checking For Correct Assembly; Emergency Manoeuvres, Maintenance And Cleaning; Troubleshooting; Environmental Protection - GIESSE VARIA SLIM Manuel D'utilisation Et D'installation

11.6. Light signals of the LED (for VARIA SLIM Syncro)
In case of a problem during installation or operation of the machines, consult the possible causes listed below:
LED Function
1 flash – pause – 1 flash - pause
2 flashes – pause – 2 flashes - pause
Continuous flash

12. CHECKING FOR CORRECT ASSEMBLY

• Check that the window has closed completely, even at the corners, and check there are no obstacles caused by assembly in the wrong position.
• Check that when the window frame is closed, the chain terminal is at least a couple of millimetres distant from the actuator body. This will ensure
correct closure of the window with correct pressure on the weather stripping. If the chain terminal is not positioned as stated there is no guarantee
the window will close correctly.
• Check that all attachments and support brackets are tightly fixed to the window frame and that all screws are correctly tightened.
• Check that the window moves to the desired position in accordance with the limit switch selected.
• Check that the gear motor support brackets are aligned and the four fixing screws are firmly screwed into position.

13. EMERGENCY MANOEUVRES, MAINTENANCE AND CLEANING

Should the window have to be opened manually in the event of no electricity, mechanical failure, or for normal maintenance or
cleaning of the external surface of the window frame, the following instructions should be followed:
1. Release the rapid release hook locking the chain terminal to the bracket.
2. Hold the window with one hand and pull the pin out of the opening with the other hand (we recommend to do so with the
opening of at least 10 cm to facilitate the release of the window) - Fig. 16.
3. Manually open the window frame.
A :
TTENTION DANGER
4. After maintenance and/or cleaning repeat points 1 and 2 in reverse order.

14. TROUBLESHOOTING

Please consult the following table for any eventual problems with function during installation or normal use:
Problem
Gear motor doesn't work.
Although selection has been carried
out correctly the gearmotor will not
take a limit switch.

15. ENVIRONMENTAL PROTECTION

All materials used in the manufacture of this appliance are recyclable.
We recommend that the device itself, and any accessories, packaging, etc. be sent to a centre for ecological recycling as established from laws in
force on recycling. The device is mainly made from the following materials: aluminium, zinc, iron, plastic of various type, cuprum. Dispose materials
in conformity with local regulations about removal.

16. CERTIFICATE OF GUARANTEE

The manufacturer will guarantee good function of the appliance. The manufacturer shall undertake to replace defective parts due to poor quality
materials or manufacturing defects in accordance with article 1490 of the Civil Code.
The guarantee covers products and individual parts for 2 years from the date of purchase. The latter is valid as long as the purchaser possesses
proof of purchase and completion of all agreed conditions of payment.
Guarantee of good function of appliances agreed by the manufacturer implies that the latter undertakes to repair or replace free of charge and in the
shortest period possible any parts that break while under warranty.
The purchaser is not entitled to any reimbursement for eventual direct or indirect damage or other expenses incurred. Attempt to repair by personnel
unauthorised by the manufacture shall render the warranty null and invalid.
The warranty does not cover fragile parts or parts subject to natural wear and tear or corrosion, overload, however temporary etc. The manufacturer
will accept no responsibility for eventual damage incurred by erroneous assembly, manoeuvre or insertion, excessive stress or inexpert use.
Repairs performed under guarantee are always "ex factory of the manufacturer". Respective transport expenses (out/back) are the responsibility of
the purchaser.
Meaning
Overload due to an
obstacle
Communication error
General synchronism
error
– the window could fall as the sash is no longer held in position by the chain.
Possible cause
• No electricity supply for feeder.
• Connecting cable not connected or wire not connected.
• Feeder doesn't deliver foreseen tension (24V═).
• Programming hasn't been carried out correctly.
• Irregular function or break in the electrical contact for the
dip-switch.
Solution
Remove the obstacle
Check the connections between the machines
Check the settings of the dip-switches or repeat the procedure for
alignment and address acquisition
• Check state of safety switch.
• Check all electrical connections of gear motor.
• Possible transformer winding break down.
• Repeat programming for dipswitch.
• Contact the Giesse technical support.
24
Figure 16
Solution