EdilKamin IDROPELLBOX 15,7 Installation, Usage Et Maintenance page 29

ASSEMBLY AND INSTALLATION
(this must be carried out by a Dealer)
e er to local regulations in the countr o use or an thing
that is not speci call covered in this manual. n tal , re er
to standard 10683/2005 in addition to an
ocal Health Authorit regulations.
the oiler-stove is to e installed in a loc o apartments,
consult the loc administration e ore installing.
VERIFY COMPATIBILITY WITH OTHER
DEVICES
The oiler- replace must
as e tractors, t pe heating appliances and other appliances
that ma a ect its operation.
VERIFYTHE POWER SUPPLY
CONNECTION
(the plug must be accessible)
The oiler- replace is supplied ith a po er ca le that is to
e connected to a 230 50 Hz soc et, pre era l
a magnetothermic s itch. oltage variations e ceeding 10%
can damage the oiler- replace unless alread installed, an
appropriate di erential s itch must e tted . The electrical
s stem must compl ith the la
e cienc o the earthing s stem. The po er line must have a
suita le cross-section or the oiler-stove's po er.
An inadequate earthing s stem can cause anomalies or hich
Edil amin cannot e held lia le.
FIRE SAFETY DISTANCES AND LOCATION
or correct operation the oiler- replace must e level. Chec
the load- earing capacit o the oor. The oiler- replace
must e installed in compliance ith the ollo ing sa et
conditions
- minimum sa et distance at the sides and ac
level amma le materials 40 cm
- easil amma le materials must not e located less than 80
cm rom the ront o the oiler-stove
- i the oiler- replace is installed on a amma le oor, a
sheet o heat insulating material must e placed et een the
oiler-stove andthe oor, hich protrudes
the sides and 40 cm at the ront.
it is impossi le to compl
technical/ uilding measures must e ta en to avoid all re
ris s. n the event o contact ith ooden alls or other am-
ma le materials, ou must insulate the smo e e haust pipe
ith ceramic re or other similar material.
AIR INTAKE
The room o installation must have an e ternal air inlet,
directl connected via duct to the special outlet provided on
the ac o the oiler- replace.
The air inlet and duct must have a diameter o 40mm in order
to ensure the suppl o the necessar amount o e ternal air
or com ustion.
a duct or direct connection cannot e made, s stem stoppa-
ge ma occur a ter the intervention o the o sensor, caused
a lac o com ustion air.
This occurs ecause the heating air suction an is located
close to the com ustion air inta e outlet and there ore, could
inter ere ith the normal o o the com ustion air.
n this case it is pre era le to move the com ustion air upta e
point appl ing a piece o tu e on the outlet, preventing the
com ustion air rom eing suc ed up
The e ternal air inta e duct must end ith a section that cur-
ves 90° do n ards or ith an anti- ind guard.
n this case, there ma e condensation pro lems and it is ne-
cessar to protect the air inta e ith a grille, hich must have
a reesection o at least 12 cm .
INSTALLATION
egional or
T e installed in the same room
tted ith
particularl veri the
rom medium
at least 20 cm at
ith the distances given a ove,
the heating air an.
The e ternal terminal o the air inlet channel must e protected
ith an anti-insect netting that does not reduce the 12 cm
through passage.
SMOKE OUTLET
The oiler- replace must have its o n smo e outlet the smo e
cannot e discharged into a smo e ue used
The smo e is e pelled rom the 8 cm-diameter outlet on the lid.
A T-section ith condensation trap and leeder must e tted
at the eginning o the vertical section.
The smo e outlet must e connected to outside
suita le steel pipes E 1856 certi ed.
The pipe must e hermeticall sealed. The material used to seal
and i necessar insulate the pipes, must e resistant to high
temperatures high temperature silicone or mastic .
The onl horizontal section allo ed ma
t ma have up to t o 90° ends.
the outlet is not tted into a chimne
and a ind guard are required re erence
The vertical duct can e internal or e ternal.
the smo e channel part o the pipe that goes rom the oiler-
replace to the chimne
l insulated.
the smo e channel is tted inside a chimne
must e suita le or solid uel.
it is ider than 150 mm in diameter it must e improved
entering a pipe that has a suita le cross-section and is made o
suita le material e.g. 80 mm diameter steel .
All sections o the smo e duct must e accessi le or inspec-
tion. it is not remova le, it must have inspection holes to
allo or cleaning.
A: internal chimne
B: e ternal ric - uilt chimne
C: internal ric - uilt chimne
D: dou le- all e ternal steel chimne
**
or the ollo ing installation, the chimne
ue must e dou le- alled and ell-insu-
**
lated or the entire length
**
respect to horizontal
CHIMNEY POT
The main characteristics are
- an internal cross-section at the ase, hich is the same as that
o the chimne ue
- an outlet cross-section hich is no smaller than t ice that o
the chimne ue
- its position must e high enough to catch the ind and avoid
do ndra t areas in tur ulent ind..
- 29
-
other devices .
means o
e up to 2 m long.
ue, a vertical section
10683/2005 .
ue is outside, it must e appropriate-
ue, the latter
**
**
ue up to the roo
ma incline o no less than 45° ith
**
ue
ue
ue