Sony LMD-3251MT Instructions D'utilisation page 84

The unit synchronizes with external sync signals when
they are detected. When external sync signals are not
detected, the unit synchronizes with internal sync
signals.
AUTO SYNC DETECT works when the component/
RGB signals are input.
AUTO SYNC DETECT does not work when signal is
input from BKM-229X.
EXT SYNC (external sync)
Press to operate the unit on an external sync signal
through the EXT SYNC IN connector.
EXT SYNC works when the component/RGB signals
are input.
If AUTO SYNC DETECT is on, this function is not
available.
MULTI DISPLAY
Press the assigned button to display the multi display.
Set the multi display setting in the MULTI DISPLAY
SETTING menu (see page 82).
DISPLAY LAYOUT
Press the button to set DISPLAY LAYOUT when the
multi display is on. The mode switches in the sequence
POP t PIP t SIDE BY SIDE with every press of the
button (see "DISPLAY LAYOUT" on page 83).
SUB INPUT SELECT
Press the button to set the sub display input signal types
when the multi display is on. The mode switches in the
sequence COMPOSITE t Y/C t RGB t
COMPONENT t OPTION A-1 t OPTION A-2 t
OPTION B-1 t OPTION B-2 t VIDEO WAVE with
every press of the button (see "SUB INPUT SELECT"
on page 83).
POSITION
Press the button to set the sub display position when the
PIP or POP multi display is on. The mode switches in
the sequence when POP is selected: 1 (Top) t 2
(Center) t 3 (Bottom), when PIP is selected: 1 (Bottom
left) t 2 (Bottom right) t 3 (Top right) t 4 (Top left)
with every press of the button (see "POSITION" on
page 83).
FRAME
Press the button to set the main display position when
the POP multi display is on. The mode switches in the
sequence RIGHT t LEFT with every press of the
button (see "FRAME" on page 83).
SUB PICTURE SIZE
Press the button to set the size of the sub display when
the PIP multi display is on. The mode switches in the
sequence 1 (Small) t 2 (Large) with every press of the
button (see "SUB PICTURE SIZE" on page 83).
84
Adjustment Using the Menus
I/P MODE
Press the button to set the delay by the picture
processing to the minimum level when interlace signal is
input. The mode switches in the sequence INTER-
FIELD t LINE DOUBLER t FIELD MERGE with
every press of the button (see "I/P MODE" on page 81).
MIRROR IMAGE
Press the assigned button to flip and display the video
signal horizontally. This function is not available for the
PRESET 1 signal and the multi display.
MONO
Press the assigned button to display a monochrome
picture. When the buttons is pressed again, the monitor
switches automatically to color mode.
APA (Auto Pixel Alignment)
Press to adjust the picture automatically to maximum
clarity for the signal input to the HD15 input connector.
For finer according to the input signal, see "DOT
PHASE" on page 80.
When the menu screen or the multi display is displayed,
APA does not function.
Note
If the APA operation does not finish correctly depending
on the input signal, adjust DOT PHASE (page 80).
BLUE ONLY
Press the assigned button to eliminate the red and green
signals. Only blue signal is displayed as an apparent
monochrome picture on the screen. This facilitates
"chroma" and "phase" adjustments and observation of
VCR noise.
2D/3D SELECT
Press the button to switch from 2D display mode to 3D
display mode. For detailed 3D display settings, select
2D/3D SELECT under the 3D SETTING menu.
Pressing the button again switches to 2D display mode.
3D SIGNAL FORMAT
Press the button to set input signal format for 3D display.
The mode switches in the sequence 3G-B t DUAL t
SEQUENTIAL t SIDE BY SIDE t LINE BY LINE
t AUTO1 t AUTO2 with every press of the button
(see "3D SIGNAL FORMAT" on page 87).
Note
This function is only available in 3D display mode.