Low Battery Warning - DeWalt DCD792 Traduction De La Notice D'instructions Originale

EnGLIsh
The dual range feature of your drill/driver allows you to shift
gears for greater versatility.
1. To select speed 1 (high torque setting), turn the tool off and
permit it to stop. Slide the gear shifter
the chuck).
2. To select speed 2 (low torque setting), turn the tool off and
permit it to stop. Slide the gear shifter back (away from
the chuck).
nOTE: Do not change gears when the tool is running. Always
allow the drill to come to a complete stop before changing
gears. If you are having trouble changing gears, make sure that
the dual range gear shifter is either completely pushed forward
or completely pushed back.
Gear speed settings are preset at the factory but can be
customized using the Tool Connect™ app. Refer to Mode
Selector table for factory presets.
LED Worklight (Fig. A)
The worklight 5 located on the foot of the tool is activated
when the trigger switch is depressed. In the Home setting,
when the trigger is released, the worklight will stay illuminated
for up to 20 seconds. If the trigger switch remains depressed,
the worklight will remain on. These settings can be customized
using the Tool Connect™ app.
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Spotlight Mode
In factory default settings, mode 3 is the spotlight mode. The
spotlight will run for 20 minutes after the trigger switch is
released. Two minutes before the spotlight will shut off, it will
flash twice and then dim. To avoid the spotlight shutting off,
lightly tap the trigger switch.

WARNING: While using the worklight in medium or
spotlight mode, do not stare at the light or place the drill in
a position which may cause anyone to stare into the light.
Serious eye injury could result.

CAUTION: When using the tool as a spotlight, be sure
it is secured on a stable surface where it will not cause a
tripping or falling hazard.

CAUTION: Remove all accessories from the chuck before
using the drill as a spotlight. Personal injury or property
damage could result.

Low Battery Warning

When in spotlight mode and the battery is nearing complete
discharge, the spotlight will flash twice and then dim. After two
TaBLE 1
Customizable Features
Worklight brightness
Worklight delay off
Maximum speed (RPM)
36
4 forward (towards
Home
MED
20 secs
Speed 1 550
Speed 2 2000
minutes, the battery will be completely discharged and the
drill will immediately shut down. At this point, replace with a
charged battery.

WARNING: To reduce the risk of injury, always have a
back-up battery or secondary lighting available if the
situation warrants it.
Keyless Single Sleeve Chuck (Fig. H–J)

WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and remove the battery from the tool when
changing acces sories.

WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool causing possible
personal injury.
Your tool features a keyless chuck
one-handed operation of the chuck. To insert a drill bit or other
accessory, follow these steps.
1. Turn tool off and disconnect tool from power source.
2. Grasp the black sleeve of the chuck with one hand and
use the other hand to secure the tool. Rotate the sleeve
anticlockwise far enough to accept the desired accessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise with
one hand while holding the tool with the other. Your tool is
equipped with an automatic spindle lock mechanism. This
allows you to open and close the chuck with one hand.
nOTE: Be sure to tighten chuck with one hand on
the chuck sleeve and one hand holding the tool for
maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
Mode Selector (Fig. A, D)
Your tool is equipped with a mode selector that allows 3 modes
15 to be customized using the Tool Connect™ app. Home
settings are active when the home indicator
Table 1 for customizable features.
Once configured, pressing the mode selector button
foot of the tool will cycle through the modes
If you are unsure of the current configuration, press the mode
selector button to set the tool to the Home setting (home
12
indicator 14 is lit).
Factory Presets
Mode 1 Mode 2
OFF MED
20 secs 20 secs
550 550
2000 2000
6 with one rotating sleeve for
14 is lit. Refer to
12 on the
15 .
Mode 3 Customizable Range
HIGH OFF-HIGH
20 minutes 0–20 minutes
550 180–550
2000 600–2000