Electrical Connection - Dexter power MS 8 Traduction Des Instructions D'origine

FIXING A WORKPIECE
Clamp the work piece on the work table with the work-
piece clamp (10 - Fig 1) in order to fix it in place.
Cross-cutting (Fig. 4, 1.3)
Attention! For 90° mitre cuts, the moveable stop rail
(27a) must be fixed in the inner position.
• Open the set screw (27b) on the moveable stop rail
(27a) with an Allen key and push the moveable stop
rail (27a) inwards.
• The moveable stop rail (27a) must be locked in a po-
sition far enough from the inner position that the dis-
tance between the stop rail (27a) and the saw blade
(5) is no more than 8 mm.
• Before making the cut, check that no collision could
occur between the stop rail (27a) and the saw blade
(5).
• Secure the locking lever (27b) again.
• Loosen the locking knob (26).
• Lift the saw unit by the handle (2) until it locks in place
in the top position.
• Lock the material with the clamping device (10) on the
fixed saw table to prevent the material from moving
during the cutting operation.
• Press the workpiece evenly on the stop strips (27);
make sure that you hand remains outside the cutting
area of the saw blade.
• With your right hand on the handle (2), press the
locking lever (3) so that the unit can also be pivoted
downward.
• The motor starts when the start button (1) is pressed.
• Slowly bring the saw blade down to the workpiece
and cut through it with moderate pressure.
• When the cutting operation is completed, move the
machine head back to its upper (home) position and
release the ON/OFF button (1).
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not re-
lease the handle (2) after completing the cut; instead
allow the machine head to move upwards slowly
whilst applying light counter pressure.
Mitre cut 0°- 45° (Fig. 1, 1.3)
The crosscut saw can be used to make mitre cuts of 0°
- 45° in relation to the work face.
Important. To make miter cuts (inclined saw head), the
adjustable stop rail (27a) must be fixed at the outer po-
sition.
• Open the set screw (27b) for the adjustable stop rail
(27a) with an Allen key and push the adjustable stop
rail outwards.
• The adjustable stop rail (27a) must be fixed far
enough in front of the innermost position that the dis-
tance between the stop rail (27a) and the saw blade
(5) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (27a) and
the saw blade (5) cannot collide.
• Secure the locking lever (27b) again.
• Move the machine head to the top position.
• Fix the rotary table (9) in the 0° position.
• Loosen the set screw (23) and use the handle (2) to
angle the machine head to the left, until the pointer
(25) indicates the desired angle measurement on the
scale (24). Retighten the fixing screw (23).
• Cut as described in section "Cross-cutting".
Saw blade replacement (Fig. 5)
• Pull out the mains plug.
• Place the saw unit in „cross-cutting" position
• Unlock the moving saw blade guard (6) by pressing
the lock (3 - Fig. 1); in the process, raise the saw
blade guard so that the saw blade is free.
• Actuate the spindle lock (22 - Fig. 3).
• Loosen the saw blade fastening screw (28) - (Atten-
tion: left-handed thread).
• Remove the screw (28) and saw blade flange (29).
• Carefully remove the saw blade (risk of injury from
the saw blade teeth).
• Place a new saw blade on the inner saw blade flange.
In the process, observe the rotational direction of the
saw blade.
• Fit the outer saw blade flange and firmly tighten the
screw.
• Move the saw blade guard back to the correct posi-
tion.
Replacing laser batteries (Fig. 6)
• Remove the laser battery cover (30). Remove the 2
batteries.
• Replace both batteries with the same or an equivalent
type. Make sure that they are inserted with the same
polarity as the used batteries.
• Close the battery cover.
Switch ON / switch OFF the laser
To switch on: Move the ON/OFF (33) switch of the la-
ser (34) to the "1" position. A laser line is projected onto
the material you wish to process, providing an exact
guide for the cut.
To switch off: Move the ON/OFF switch of the laser to
the "0" position.
m Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions.
The customer's mains connection as well as the
extension cable used must also comply with these
regulations.
Important information
In the event of an overloading the motor will switch itself
off. After a cool-down period (time varies) the motor can
be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
(Fig. 6)
GB 25