Commissioning; Area Of Application; Settings; Working Instructions - Dexter power MS 8 Traduction Des Instructions D'origine

• Afterwards, retighten the locking screws (17).
Assembling the work piece supports (fig. 1.1 – 1.2)
• Loosen the cross-head screw (14) and guide the work
piece support through the specified hole on the side
of the fixed saw bench.
• Make sure that the work piece support (15) is also
guided through the two plates (19) on the underneath.
• Afterwards, retighten the cross-head screw (14).
• Repeat this process on the other side.
Assembling the support stand (fig. 1.1 – 1.2)
• Loosen the cross-head screws (18) on the underneath
of the saw and guide the support stand (16) through
the specified holes on the back of the saw.
• Afterwards, retighten the cross-head screws (18).

Commissioning

Prior to commissioning, observe the safety instruc-
tions in the operating instructions.
Do not use the tool if the main switch can not be
switched from the ON to the OFF position.
Have defective main switches replaced by author-
ised customer service personnel.
REMOVAL FROM THE PACKAGING
Remove the machine from its package, which protects
it during transport, without damaging the package in or-
der to be able to use it later for transporting the mitre
saw for long-term storage.
MOVING
Since the mitre saw is relatively small and light, its loca-
tion can be easily changed, even by a single person.
After locking the locking knob (26 - Fig. 4) in the bottom
position, lift the mitre saw by the handle (34 - Fig. 4).
TRANSPORT
If the machine must be transported, carry it by the han-
dle (34 - Fig. 4) and place it in the original packaging in
which it was supplied. In the process, make sure that
it is correctly positioned in the package (see arrows on
the package).
If possible, the load should be fixed with ropes or secur-
ing belts in order to prevent shifting during the transport
or parts of the load from falling down.
POSITIONING/WORK STATION
Position the machine on a work bench or on a flat base
so that the machine is supported as stably as possible.
When working with the machine, ergonomic factors
must be considered; the ideal height of the work table
or the base is reached when the base surface or the
upper work surface is 90 to 95 cm above the ground.
The positioning of the machine must provide for at least
80 cm of clearance in all directions and in order to al-
low for cleaning and repair work as well as necessary
adjustments in observance of safety conditions and with
sufficient room to manoeuvre.
24 GB
CAUTION: Position the machine in a zone which is
suitable in respect to the environmental conditions and
lighting. Never forget that the general environmental
conditions play an extremely important role in accident
prevention.
CONNECTION TO THE POWER SUPPLY
Make sure that the socket is in a good condition. We
would like to remind you that the power supply must be
connected to a magnetic-thermal circuit breaker which
protects all lines from short-circuits and overloading.
m Area of application
Intended application possibilities
The machine cuts:
• Wood and materials similar to wood
• Plastic
Unintended application possibilities
The machine is not suitable for:
• Ferritic materials, steel and cast iron, as well as other
material types which are not listed, particularly food.
• Mitre saw without guard.
• Materials larger than the specified cutting data:
90°/90°/
90°/45°
45°/90°
45°/45°

Settings

CROSS-CUTTING
ATTENTION: Before carrying out the following adjust-
ments, please check whether the motor of the machine
is switched off.
Pivoting the table plate (Fig. 2)
The mitre saw can be pivoted left and right with the rota-
ry table. Exact angle adjustment is possible on the basis
of the scale. The angle can be precisely and quickly ad-
justed from 0° to 45° with locking positions at 15°, 22.5°
and 30°.
To pivot the rotary table, loosen the set screw (21) and
rotate the unit using the handle (20) until the desired an-
gle is reached. Then secure it with the set screw (21).
Tilt of the saw unit (Fig. 3)
The saw unit can be tilted at an angle of up to 45°.
Loosen the handle (23) on the rear side of the machine
and tilt the unit to the desired angle position according
to the scale. The angle can be set on the basis of the
scale (24) using the pointer (25). Then the handle must
be re-tightened.

Working instructions

After you have carried out all the tasks described above,
you can begin working.
ATTENTION: Always keep your hands away from the
cutting zone and never attempt to reach in while cutting.
120 x 60 mm
80 x 60 mm
120 x 35 mm
80 x 35 mm