Zurückstellen Der Überhitzungsschutzes - Sentiotec 145 Instructions D'installation Et Mode D'emploi

Table des Matières

Publicité

EN
3.5. Resetting the Overheat Protector
If the temperature of the sauna room becomes dan-
gerously high, the overheat protector will permanent-
ly cut off the supply of the heater. The overheat pro-
tector can be reset after the heater has cooled down.
145-190
The reset button is located on the thermostat frame
on the electrical box (see fig. 12), and consequently,
the fuses of the heater on the electrical panel must
be removed before commencing the work. Only per-
sons authorised to carry out electrical installations
can reset the overheat protector.
Prior to pressing the button, the cause of the fault
must be found.
Are the stones crumbled and pressed together?
Has the heater been on for a long time while
unused?
Is the sensor of the thermostat out of place or
broken?
Has the heater been banged or shaken?
1. Open the fixing screw of the control end from
the bottom of the electrical box so that about
10–12 mm of the thread of the screw can be
seen.
2. Pull the end-piece carefully out of the box.
Detach the adjusting wheel of the thermostat
and the thermostat frame from their supports
(4 locking cams), carefully pressing the
adjusting shaft at the same time. The
thermostat frame will move backwards about
40 mm, and the reset button of the limit stop
is revealed.
3. Reset the limit stop by pressing (with 7 kg
force if necessary) so that a clicking sound is
heard.
4. After pressing the reset button, replace the
thermostat frame and press the adjusting wheel
onto the shaft.
5. Prior to tightening the fixing screw of the end-
1-E
2-E
Figure 11.
Installing the sensor (all dimensions in millimeters)
Abbildung 11. Installation der Fühler (alle Abmessungen in Millimetern)
DE
3.5. Zurückstellen der Überhitzungsschutzes
Wenn die Temperatur in der Saunakabine gefährlich
stark ansteigt, unterbricht der Überhitzungsschutz
die Stromzufuhr zum Ofen permanent. Der Überhit-
zungsschutz kann nach Abkühlen des Ofens zurück-
gesetzt werden.
145-190
Der Rücksetzknopf befindet sich in der Elektro-
buchse im Rahmenteil des Thermostats (siehe Abb.
12), daher müssen die Saunaofensicherungen an
der Elektrotafel zunächst gelöst werden. Nur eine
zu Elektroinstallationen befugte Person darf diese
Arbeit ausführen.
Vor Betätigung des Knopfes muß die Ursache der
Fehlfunktion festgestellt werden:
Sind die Steine im Saunaofen verkeilt oder spröde?
War der Saunaofen lange angeschaltet und
wurde nicht benutzt?
Ist der Thermostatfühler an einem falschen
Platz oder defekt?
War der Saunaofen starken Stößen ausgesetzt?
1. Die Befestigungsschraube des Stirnstücks mit
den Steuergeräten wird aus dem Boden der
Elektrobuchse herausgeschraubt, so daß der
Gewindeteil zu ca. 10–12 mm sichtbar wird.
2. Das Stirnstück wird vorsichtig von der Buchse
abgezogen. Das Stellrad des Thermostats wird
gelöst und der Thermostatrahmen von sei-
nen Halterungen (4 Stk. Sperrnocken) befreit,
wobei gleichzeitig die Steuerungswelle vor-
sichtig heruntergedrückt wird. Das Rahmenteil
des Thermostats bewegt sich ca. 40 mm nach
hinten, wobei an dessen Vorderseite der Rück-
setzknopf des Begrenzers erscheint.
3. Der Begrenzer wird durch Druck in seine Funkti-
onsstellung zurückgesetzt (bei Bedarf mit einer
Kraft, die 7 kg entspricht), im Begrenzer ist
dann ein Knacken zu hören.
4. Setzen Sie nach Drücken des Rücksetzknopfes
das Rahmenteil des Thermostats an seinen Platz
und schieben Sie das Stellrad auf die Welle.
5. Stellen Sie vor Festziehen der Schraube am
Figure 12.
Reset button for overheat protector (1)
Abbildung 12.
Rücksetzknopf des Überhitzungsschutzes (1)
19

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

160180190145e160e180e ... Afficher tout

Table des Matières