Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Ordering Replacement Parts; Disposal And Recycling - EINHELL BT-HP 1435 Mode D'emploi D'origine

Masquer les pouces Voir aussi pour BT-HP 1435:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 26
6.2.1 Using detergent with the solid cone /
fl at fan lance
Set the solid cone / fl at fan lance (Fig. 10) to low-
pressure mode (n).
6.3 Holder for the gun/accessories (Fig. 7)
To save space when not in use, the gun and ac-
cessories can be kept in the holder provided.
Caution! Before using the pressure cleaner,
make sure that the high-pressure hose is comple-
tely unwound.

7. Replacing the power cable

If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment. En-
sure that no water can seep into the device.
8.2 Maintenance
8.2.1 Testing the water intake fi lter
Periodically check the intake fi lter in order to pre-
vent clogging, which could jeopardize operation
of the pump.
To do this, unscrew the coupling for the water inlet
hose from the device and clean the exposed inlet
sieve under running water.
Anl_BT_HP_1435_SPK1.indb 21
Anl_BT_HP_1435_SPK1.indb 21
GB
8.2.2 Long periods of nonuse (electric pump)
If the equipment is going to be stored for longer
periods of time (i.e. over three months) in a room
where the temperature could drop below freezing
point, it is recommended that the equipment be
fi lled with an antifreeze solution (similar to the an-
tifreeze solutions used for vehicles).
If the device is not used for an extended period
of time, lime deposits will begin to form in the
electric pump, which in turn can lead to starting
diffi culties.
8.2.3 Cleaning the nozzle (Fig. 9)
Use the supplied wire (A) to clean clogged nozz-
les.

8.3 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
9. Transport
Before transporting the equipment to a diff erent
location, remove all connections. The equipment
is then free for transport.

10. Disposal and recycling

The unit is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic. De-
fective components must be disposed of as spe-
cial waste. Ask your dealer or your local council.
11. Storage
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempe-
rature is between 5 and 30 °C. Store the electric
tool in its original packaging.
- 21 -
31.07.12 14:40
31.07.12 14:40

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

41.404.80

Table des Matières