Using For The Fi Rst Time; Using Detergent - EINHELL BT-HP 1435 Mode D'emploi D'origine

equipment.
Caution: Risk of explosion
Do not spray fl ammable liquids.
Warning
Water that has passed through the non-return
valve is not drinkable.
Warning
If cleaning agent gets into contact with your skin
or into your eye, rinse immediately with lots of
clean water. Then consult a doctor or follow the
steps described on the safety data sheet or provi-
ded by the manufacturer of the cleaning agent.
5.2 Assembly
5.2.1 Assembling the equipment
Assemble the pressure cleaner as shown in Fi-
gure 2-6.
5.2.2 Water inlet connector (Fig. 1/4)
The connection for the water inlet (4) is equipped
with a connector for standard hose coupling sys-
tems. Plug the hose coupling on the supply hose
(min. Ø 1/2") to the water inlet connector (4).
A backfl ow preventer must be installed between
the drinking water and the pressure cleaner! Ask
your local plumber about this.
5.2.3 Connecting the high-pressure hose
(Fig. 1-3; 5-6)
Remove the transport brace as shown in Figure 5
from the high-pressure hose connector (9). Con-
nect the high-pressure hose (18) to the connector
on the pressure cleaner (9) and to the connector
on the spray gun (14).
5.2.4 Fitting the gun attachments
You can attach either the normal lance or the
lance with rotating nozzle (Fig. 2) before the pres-
sure cleaner is used.
Solid cone / fl at fan lance (16)
The shape of the water jet can be changed from
solid cone to fl at fan by turning the nozzle (Fig. 8).
Lance with rotating nozzle (17)
To remove particularly stubborn dirt, use the lance
with the rotating nozzle (17).
Anl_BT_HP_1435_SPK1.indb 20 Anl_BT_HP_1435_SPK1.indb 20
GB
5.2.5 Electrical connections (Fig. 1)
•
Before you connect the equipment to the
power supply make sure that the data on the
rating plate are identical to the supply voltage.
•
If you use any extension cables, make sure
that they are suitable for outdoor use and
have large enough wires:
1 – 10 m: 1.5 mm²
10-30m: 2.5 mm²
•
Insert the power plug (8) on the power cable
(6) into the socket outlet.
6. Operation
The equipment consists of an assembly with a
pump, which is encased in a shock absorbing
housing. For an optimal working position the
equipment comes with a lance and a non-slip
gun, whose shape and confi guration comply with
the applicable regulations.
6.1 Using for the fi rst time
Once you have completely assembled the pres-
sure cleaner and made all the connections, pro-
ceed as follows:
Open the water inlet. Press safety pin „a" (Fig. 2)
on the spray gun and pull back trigger lever „b"
(Fig. 2) in order to bleed the trapped air out of the
equipment.
Turn on the equipment by switching the On/Off
switch (Fig. 1/3) to "ON".
To turn off , release the trigger lever (b). The
equipment will then go into standby. As soon as
you press the trigger lever (b) again, the pressure
cleaner will restart.
To turn off the pressure cleaner completely, set
the On/Off switch (Fig. 1/3) to "OFF".

6.2 Using detergent

•
Fill the detergent tank (10) with a suitable
cleaning agent.
•
The detergent will be added automatically in
low-pressure mode.
•
Detergent may be used only together with the
following accessories.
- 20 -
31.07.12 14:40 31.07.12 14:40