EdilKamin BIG Installation, Usage Et Maintenance page 16

COVERING INSTALLATION BIG/VIP
10
9
54
33
fig. 1
78
150
57-58
139
fig. 3
150
75
139
fig. 5
150
fig. 6
78
41
fig. 8
23
22
22
43
fig. 10
78
75
fig. 2
140
fig. 4
150
150
114
27
130
115
57 57
150
150
29
114
58 58
115
58 58
29
150 150
detail. "Y"
28
150 150
4
fig. 7
139
150
41
41
150
150
150
41
41
150
150
fig. 9
DETAIL. Z
Part. "Z"
22
62
bushings
23
24
screw
vite
fig. 11
INCLUDED HARDWARE:
2 M6x25 screws
2 M6x12 screws
4 silicone spacers for ceramic top
8 flat washers diam. 6
2 bushings
16 silicone spacers for ceramics
2 ceramic fixing plates
ASSEMBLING THE LATERAL TILES (fig. 1-2)
• Remove the rear panel (54) And the two profiles (9-10).
• Fix the two plates (78) to the zinc-plated sides where three
holes are located (to be used according to the models).
150
for the VIP model (Illustr. 3-4)
150
150
• The left-hand plate must be fixed to the central and upper
holes, whilst the right-hand plate must be fixed to the central
139
57 and lower holes.
• Fit the ceramic tiles (57-58) on to the plates (78)
• Place 2 silicone-coated spacers (150) in the lower part betwe-
en the cast iron base and the lower, right-hand tile (58) (see
150
150
detail Y - Illustr. 4).
62
150
• For correct fastening of the upper right side ceramic tile and
the lower left side ceramic tile use the stop adjustment screws
located on the zinc-plated sides of the structure (Illustr. 5-6)
139
• Right-hand side (Illustr. 5): adjust the fixing screw abutted
against the upper right side ceramic tile (57).
62
• Left-hand side (Illustr. 6): remove the upper left ceramic tile
(57) and adjust the fixing screw abutted against the lower left
150
side ceramic tile (58).
• Replace the upper left ceramic tile (57).
for the BIG model (Illustr. 8-9)
• The left-hand plate must be fastened to the central and lower
hole, whilst the right-hand plate must be fastened to the central
and upper hole.
• Fit the ceramic tiles (41) on to the plates (78)
NOTE: Being made through a process of casting,the tiles may
150
differ slightly in height. To compensate for any height varia-
tions, silicone spacers may be inserted (150 - fig. 4-9) without
affecting the aesthetic appearance of the stove.
• Replace the profiles (9-10) Replace the rear panel (54).
ASSEMBLING THE UPPER FRONT PANEL BIG/VIP
(fig. 10-11)
• Position the ceramic upper front panel (22) so that it rests
against the front panel support (23) positioned above the door.
• Use an Allen key to fasten the front panel in place using
62
the 2 supplied M6x25 screws (the door must be opened before
performing this operation).
NOTE: For correct assembly of the upper front panel (22), pla-
ce the bushing supplied between the same and the front panel
(23), as shown in detail "Z" in Illustr. 11.
ASSEMBLING THE LOWER FRONT PANEL BIG/VIP
(fig. 10-12)
• Use the supplied Allen key to loosen the screws that hold
the cast iron lower front grill (43) in place and remove it.
• Position the front panel (22) and use an Allen key to
fasten it in place using the 2 supplied M6x25 screws as indica-
ted in detail "X" (fig. 12).
- 16
-
139 139
150
62
n°2 viti
Part. "X"