Scheppach HM90SL Traduction Des Instructions D'origine page 23

– Connect a dust collecting device to the electric
tool when sawing wood. The emission of dust
is influenced, among other things, by the type
of material to be processed, the significance of
local separation (collection or source) and the
correct setting of the hood/guide plates/guides.
– Do not use saw blades made of high­speed
alloy steel (HSS steel).
2 Maintenance and repair
– Pull out the mains plug for any adjustment or
repair tasks.
– The generation of noise is influenced by vari-
ous factors, including the characteristics of saw
blades, condition of saw blade and electric tool.
Use saw blades which were designed for re-
duced noise development, insofar as possible.
Maintain the electric tool and tool attachments
regularly and if necessary, initiate repairs in or-
der to reduce noise.
– Report faults on the electric tool, protective de-
vices or the tool attachment to the person respon-
sible for safety as soon as they are discovered.
3 Safe work
– Make sure that a suitable saw blade for the ma-
terial to be cut is selected.
– Never use the machine to cut other materials as
specified.
– To transport the machine follow the procedure
of point 9. When transporting the electric tool,
only use the transport devices. Never use the
protective devices for handling or transport.
– Operate the machine only if the protective de-
vices are functional, in good condition and in the
correct position.
– The floor around the machine must be level,
clean and free of loose particles, such as chips
and cutting residues.
– Only use saw blades for which the maximum
permissible speed is not lower than the maxi-
mum spindle speed of the machine and which
are suitable for the material to be cut.
– Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for the
intended purpose.
– Attention! Do not replace the laser by a differ-
ent type. Repairs may only be carried out by the
manufacturer or an authorized representative.
– Do not remove any cutting residues or other
parts of workpieces from the cutting zone while
the machine is running and the saw unit is not
at rest.
Instructions for proper and safe sawing:
a) Clamp the workpiece always at the saw table
firmly. Therefore please use the supplied clamp-
ing device.
b) Make sure that the machine is secured before
each sawing;
c) If necessary attach the machine to a workbench
or the like. Fasten the machine to the workbench,
using the holes at the fixed saw table.
d) Support long workpieces (e.g. with a roller table)
to prevent them sagging at the end of a cut.
e) Make sure that the saw blade does not touch
the rotary table in any position by pulling out the
mains plug and rotating the saw blade by hand in
the 45° and 90° position. If necessary, readjust
the saw head.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
SAFETY INSTRUCTIONS FOR THE HANDLING
OF SAW BLADES
1 Only use insertion tools if you have mastered
their use.
2 Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
3 Observe the motor / saw blade direction of rota-
tion.
4 Do not use any insertion tools with cracks. Sort
out cracked insertion tools. Repairs are not per-
mitted.
5 Clean grease, oil and water off of the clamping
surfaces.
6 Do not use any loose reducing rings or bushes
for the reducing of holes on saw blades.
7 Make sure that fixed reducer rings for securing
the insertion tool have the same diameter and
have at least 1/3 of the cutting diameter.
8 Make sure that fixed reducer rings are parallel
to each other.
9 Handle insertion tool with caution. They are ide-
ally stored in the originally package or special
containers. Wear protective gloves in order to im-
prove grip and to further reduce the risk of injury.
10 Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
11 Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
12 Only use the supplied saw blade for cutting wood,
never for the processing of metals.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
GB 23