Technical Specifications; Declaration Of Conformity - STEINEL Studioline 300 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
Troubleshooting
Malfunction
Cause
IS 300 without power
a
Fuse has blown; not
switched ON
a
Short circuit
IS 300 does not switch ON
a
Twilight setting in
nighttime mode during
daytime operation
a
Bulb burnt out
a
Mains switch OFF
a
Fuse blown
a
Detection zone not
correctly adjusted
IS 300 does not switch OFF
a
Continued movement
within the detection zone
a
Switched on light is within
detection zone and
switches on again as a
result of temperature
change
a
Set to continuous
operation by indoor series
switch
IS 300 keeps switching
a
Switched on light is within
ON/OFF
detection zone
a
Animals moving in
detection zone
IS 300 switches on when it
a
Wind is moving trees and
should not
bushes in the detection
zone
a
Cars in the street are
detected
a
Sudden temperature
changes due to weather
(wind, rain, snow) or
exhaust air from fans or
open windows
18

Technical specifications

Remedy
Dimensions (H x W x D):
Output:
a
Replace fuse, switch on
mains switch, check wiring
with voltage tester
a
Check connections
a
Readjust
Connection:
a
Replace light bulb
Angle of coverage:
a
Switch power on
Pivoting range of the sensor:
a
Replace fuse, check
connection if necessary
Reach:
a
Readjust
Time setting:
Twilight setting:
Type of enclosure:
a
Check zone and readjust if
necessary or apply shroud
a
Readjust zone or apply
shroud
This product complies with
a
Series switch to automatic
the European Directive on
Low-Voltage Appliances,
a
Adjust detection zone or
apply shrouds, increase
distance
Functional Warranty
a
Adjust detection zone or
apply shrouds
This STEINEL product has
been manufactured with great
a
Adjust detection zone or
care, and its operation and
apply shrouds
safety have been tested in
conformity with the current
a
Adjust detection zone or
regulations. Production is
apply shrouds
also submitted to final ran-
a
Adjust detection zone or
dom-sample testing.
install in a different place
90 x 60 x 100 mm
max. 2000 W (ohmic load, e.g. filament bulb)
max. 1000 W (uncorrected, inductive,
max. 1800 W (series corrected)
max. 500 W (parallel corrected with C = 45.6 µF)
max. 1000 W (electronic ballast, capacitive,
230 – 240 V, 50 Hz
300° with 180° angle of aperture
Fine adjustment ± 80°
max. 12 m (electronically stabilised)
10 sec. – 15 min.
2–2000 lux
IP 54

Declaration of conformity

73/23/EEC and the EMC
Directive 89/336/EEC.
STEINEL undertakes the
guarantee for perfect condi-
tion and function.
The warranty period is
36 months, starting on the
date of sale to the user. We
undertake to remedy faults
caused by material or manu-
facturing defects. This war-
ranty undertaking shall be
performed by the repair or re-
placement of the defective
parts, at our own discretion.
This warranty shall not cover
damage to wearing parts or
damage and faults caused by
incorrect operation or main-
tenance. Breakage due to a
fall is also not covered.
Further consequential dam-
age to external items is ex-
cluded.
cos φ = 0,5, e.g. fluorescent lamps)
e.g. energy-saving lamps,
max. 12 items)
Claims under warranty shall
only be accepted if the prod-
uct is sent fully assembled
and well packed complete
with sales slip or invoice
(date of purchase and deal-
er's stamp) to the appropriate
Service Centre or handed in
to the dealer within the first
6 months.
Repair Service:
Our Customer Service De-
partment will repair faults not
covered by warranty or after
the warranty period. Please
send the product well packed
to your nearest Service
Centre.
19

Publicité

Table des Matières
loading

Table des Matières