Parameter Settings; Explanation Of The Parameter Tables; Operating Mode - Daikin EHSX04P30D Manuel D'utilisation

7

Parameter settings

7.1 Explanation of the parameter
tables
The parameter tables listed in Chap. 7.2
pact information on all parameters that are available in the respect-
ive menus and submenus of the controller (1st menu level, 2nd
menu level).
In addition to the parameter designations, the tables contain informa-
tion on setting ranges, factory settings, setting options or adjustment
steps and brief explanations of the function.
In addition, they provide an explanation of the access rights for oper-
ation of the control unit. The following abbreviations are used for cor-
responding labelling:
BE Access right for the operator
7.2

Operating mode

[→ Main menu → Operating mode]
Parameters Setting range
Min / Max
Standby
Reducing
Heating
Summer
Automatic 1
Automatic 2
Cooling
Tab. 7-4 Parameter in menu: "Operating mode"
Daikin RoCon+ HP
Daikin Controller RoCon+ HP
008.1444299_01 – 09/2018 – EN
to Chap. 7.10 contain com-
Description
In this operating mode all internal functions are switched off. Frost protec-
tion remains active and a blocking protection for the pump is guaranteed.
All controllers integrated in the RoCon system via the CAN bus are primar-
ily also switched to the operating mode if this setting is selected.
Outputs are not always completely free of voltage.
The internal HC continuously regulates to the required reduced feed tem-
perature according to the [Heat-Slope] or [Feed temperature reducing
mode] parameters or to the room temperature [Room temperature reduced]
if the room thermostat is connected. Domestic hot water preparation is car-
ried out according to [Hot water automatic 1].
The internal HC continuously regulates to the required feed temperature
according to the [Heat-Slope] or [Feed temperature heating mode] para-
meters or to the room temperature [Room temperature setpoint 1] if the
room thermostat is connected. Domestic hot water preparation is carried
out according to [Hot water automatic 1].
The internal HC is switched off. Frost protection remains active and a
blocking protection for the pump is guaranteed. Domestic hot water prepar-
ation is carried out according to [Hot water automatic 1].
All controllers integrated in the RoCon system via the CAN bus are primar-
ily also switched to the operating mode if this setting is selected.
The internal heating circuits are controlled according to the set [Heating cir-
cuit automatic 1] time program with the respective room target temperat-
ures. Domestic hot water preparation is carried out according to [Hot water
automatic 1].
The internal heating circuits are controlled according to the set [Heating cir-
cuit automatic 2] time program with the respective room target temperat-
ures. Domestic hot water preparation is carried out according to [Hot water
automatic 2].
The internal heating circuit continuously regulates to the required feed tem-
perature according to the parameters in the menu [→ Main menu→ Config-
uration→ Cooling] or to the [Room temperature setpoint 1] room temperat-
ure if the room thermostat is connected. Domestic hot water preparation is
carried out according to [Hot water automatic 1]. Frost protection remains
active and a blocking protection for the pump is guaranteed.
7
HF Access right with technician code
If different entries are made in the BE and HF columns, the
technician must be logged in before selecting the parameter
level in order to obtain the status entered in the HF column
(see Chap. 4.5 ).
Status:
N Not visible
E Visible and configurable
S Visible
INFORMATION
Changing some parameters requires a restart of the
device. This takes a few minutes. No further settings can
be made during this time. The restart can be delayed by
5 minutes by selecting "Later" in response to the "Restart
required. Perform now?" prompt.
Parameters that require a restart are marked with (*) in the
following tables
Parameter settings
Factory Incre- Access
setting ment
BE HF
- E E
- E E
- E E
- E E
- E E
- E E
- E E
Operating Instructions
29