Components And Description; Coating Materials Not Suitable For Use - WAGNER ProjectPro 119 Manuel D'utilisation

WAGNER Project Pro 119 - 0418C - Safety Information
When working outdoors:
Vapors containing solvents may not be allowed to
blow toward the unit.
Note the direction of the wind.
Danger
Set the unit up in such a way that vapors containing
solvents do not reach the unit and build up there.
A minimum distance of 5 m between the unit and
spray gun is to be maintained.
Cleaning the unit
U
Danger of short circuit through penetrating water!
Never spray down the unit with high-pressure or
high-pressure steam cleaners.
Danger

Components and Description

The shipping carton for your painting system contains the following:
• Suction line (including inlet filter) and return line (including metal clip)
• 15 m, 6.35 mm internal diameter pressure hose
• Spray gun with two filters (L-XXL; one in gun, one separate)
• Hose bracket
Figure 1 - Controls and Functions
(further, detailed descriptions of the individual items can be found in the relevant section of the operating instructions)
Item Component
A) ON / OFF Switch ............................The ON/OFF switch turns the power to the sprayer on and off (O=OFF, l=ON).
B) PRIME / SPRAY Knob ....................The PRIME/SPRAY knob directs fluid to the spray hose when set to SPRAY or the return tube when set
C) Sureflo™ Valve ................................The Sureflo™ valve is designed to keep the inlet valve open and from sticking due to dried materials.
D) PressureTrac™ ................................The PressureTrac™ regulates the amount of force the pump uses to push the fluid.
E) Pump Section .................................A piston in the pump section moves up and down to create the suction that draws fluid through the
F) Suction Tube ..................................Fluid is drawn through the suction tube into the pump.
G) Return Tube ....................................Fluid is sent back out through the return tube to the original container when PRIME/SPRAY knob is in
H) Inlet filter ..........................................The inlet filter strains the spray material to prevent the system from becoming clogged.
I) Hose bracket ...................................Attach the hose bracket by inserting the ends of the bracket into the holes of the handle as shown.
J) Spray Gun ........................................The spray gun controls the delivery of the fluid being pumped.
K) Spray Hose ......................................The spray hose connects the gun to the pump.
Technical Data
Pump type
Power source
Power consumption
Fusing
Double insulation
Max. spray pressure
Max. delivery rate
Sound pressure level
Oscillation level
Max. temperature of coating
substance
Max. nozzle size
Hose length
Weight
Description
to PRIME. The arrows on the PRIME/SPRAY knob shows the rotation directions for PRIME and SPRAY.
The PRIME/SPRAY knob is also used to relieve pressure built up in the spray hose (see Pressure Relief
Procedure).
The Sureflo™ valve is activated automatically every time you turn the ON/OFF switch ON.
suction tube.
PRIME position.
Piston pump
230-240 V 50 Hz
~
720 W
Only connect to sockets protected
with an FI fuse (16 A)
200 bar
1,3 l/min
71,2 dB (A)
< 2,5 m/s²
40°C
XL (0,019")
15 m
18 kg
Cleaning units with solvents
U
When cleaning the unit with solvents, the solvent
should never be sprayed or pumped back into a
container with a small opening (bunghole). An
explosive gas/air mixture can be produced. The
Danger
container must be earthed.
Do not clean the device or accessories with
flammable solvents with a flash point below 21 °C.
Earthing of the object
U
The object to be coated must be earthed.
• Spray tip assembly
• Basic unit
• Instruction manual
• Oil flask
Coating Materials Suitable for Use
Water-based and solvent-containing lacquers and glazes.
Paints, oils, release agents, synthetic enamels, PVC lacquers,
undercoats, base coats, fillers and anti-rust paints.
Dispersion and latex paints for interior use.

Coating Materials Not Suitable for Use

Materials that contain highly abrasive components, facade paint,
caustic solutions and acidic coating substances.
Materials with a flash point below 21°C.
In order to ensure compatibility of the coating substance
i
with the materials used to manufacture the device, please
contact Wagner Service in cases of doubt.
15