Efco DS 5300 S Manuel D'utilisation Et D'entretien page 32

(L) to block the blade and allow the bolt (A) to be
tightened to 2.5 kgm (25 Nm).
T - Push the button (G) to block the blade and
allow the nut (A) to be tightened to 3 kgm (30 Nm).
WARNING – Collar (see arrows C, Fig.9)
must locate in blade's mounting hole.
FITTING THE HANDLE (Fig. 2)
Fit the handle onto the shaft arm and secure it
using screws (A). The handle position is calculated
depending on the requirements of the operator.
WARNING - Assemble the handle (D, Fig.2-
3) between label's arrow (B) and rear handle (C).
ASSEMBLING THE SAFETY BOOM (Fig. 7)
When using the disc instead of nylon line head, it
is necessary to set up the "safety boom". Fix the
boom (A) under the attachment (C) of handle (20B,
Fig. 1) by means of the screws (B). Taking care to
verify the "safety boom" being on the left side of
the brushcutter.
MOUNTING THE CONTROL HANDLES (Fig. 5)
- Loosen the screw (G, Fig.6). The nut (H) remains
in the control handle (L).
- Push the control handle (L) (throttle trigger M
must point toward the gearbox) onto the bike
handle (N) so that the holes (P) line up.
- Insert screw (G) and tighten down firmly.
ASSEMBLING THE BIKE HANDLE (Fig. 6)
- To fix the handle, insert the spring (B) and washer
(C)
- Line up the handlebar at a right angle to the
drive tube (20A, Fig. 1).
- Then tighten the clamp with the screw (D).
WARNING:
components are connected properly and all
screws tightened.
PREPARING TO WORK
Make sure that
HARNESS (4S, Fig. 1)
Correct adjustment of the harness permits the
brush cutter to be properly balanced and at an
appropriate height from the ground (Fig. 10).
- Put on the single harness.
- Hook the brush cutter to the harness using the
hook (A, Fig. 10).
- Position the hook (19, Fig. 1) to obtain the best
brush cutter balance.
- Position the buckle to obtain the correct brush
cutter height.
CORRECT ADJUSTMENT OF THE HARNESS
DS 5300 T - BC 530 T - DS 5500 Boss - BC 550
Master models
1. Put on the double harness (4T, Fig.1).
2. Fasten the waist buckle (A, Fig.12) and adjust
by tightening the top belt strap (B) until
comfortable.
3. Fasten the chest buckle (C).
4. Adjust the shoulders by tightening the two
straps (D, Fig.13) until comfortable. With this
type of harness, the weight of the machine can
be distributed between shoulders and waist
according to the preference of the operator.
5. Adjust the chest strap (E, Fig.12).
6. Hook the brushcutter to the harness with the
snap (A, Fig.10).
7. Adjust the carrying height by shortening or
lengthening the belt straps (H-L, Fig.14). The
correct distance between the belt and the
snap can be measured as in Fig.10. This
adjustment will also help to distribute the
weight of the brushcutter so that it stays
comfortably balanced during operation.
WARNING! – When using wood-cutting
blades (22-60-80 teeth) a double harness with
quick-release mechanism must be worn.
APPROVED POWER TOOL ATTACHMENTS
The following Emak attachments may be mounted
all
to the basic power tool:
EP 100 Pole pruner (1)
(1) Not approved for use with bike handle units
(DS 5300 T - BC 530 T - DS 5500 Boss - BC 550
Master).
GB
27