Technical Data; Before Starting The Equipment - EINHELL GE-CG 18 Li Instructions D'origine

4. Technical data

Speed n : ............................................. 1200 rpm
0
Cutting width of the grass cutter: ............ 100 mm
Cutting width of the shrub shears ........... 200 mm
Cutting thickness of the shrub shears ........ 8 mm
L sound pressure level: ................... 63.4 dB (A)
pA
L sound power level: ...................... 83.4 dB (A)
WA
K uncertainty ...................................... 2.09 dB (A)
Vibration a : .......................................... 2.5 m/s
h
Weight: .....................................................0.66 kg
Sound pressure level
at the operator's ear .............................. 72 dB (A)
K uncertainty ........................................... 3 dB (A)
Important!
The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
Power-X-Change
18 V, 1.5 Ah .............................. 5 lithium-ion cells
18 V, 2.0 Ah .............................. 5 lithium-ion cells
18 V, 3.0 Ah ............................ 10 lithium-ion cells
18 V, 4.0 Ah ............................ 10 lithium-ion cells
18 V, 5.2 Ah ............................ 10 lithium-ion cells
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Charging unit
Mains voltage ................... 200-250 V ~ 50-60 Hz
Output
Rated voltage ........................................ 21 V d. c.
Rated current ....................................... 3000 mA
The vibration emission level has been measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
•
The specified emission level can also be
used to make an initial assessment of the ex-
posure to vibrations.
•
The vibration emission level may vary from
the level specified during actual use, depen-
ding on the way in which the power tool is
used.
GB
•
Try to keep the impact from vibrations as low
as possible. Exposure to vibrations can be re-
duced by wearing gloves when using the tool,
for example, and by limiting the amount of
operating time. This includes the full cycle of
operation (e.g. times when the power tool is
switched off and times when the tool is swit-
ched on but no working load is applied).

5. Before starting the equipment

2
The equipment is supplied without batteries
and without a charger.
5.1 Charging the battery (Fig. 3-4)
1. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the mains socket outlet. The green LED
will then begin to ash.
2. Insert the battery pack into the battery char-
ger.
3. In section "Charger indicator" you will nd a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless hedge trim-
mer drops. Never fully discharge the battery pack.
This will cause it to develop a defect.
5.2 Battery capacity indicator (Fig. 5)
Press the switch for the battery capacity indicator.
The battery capacity indicator shows the charge
status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
- 17 -