Technical Data; Part Description (Fig. 1); Safety Devices; Intended Use - Tecomec Sharp Master Manuel D'utilisation

7. TECHNICAL DATA

Model
Voltage
Rated power
Grinding wheels
dimensions
Maximum speed of
grinding wheel
Operating time
Acoustic pressure level
Acoustic power level
Level of vibrations on
operating handle ( * )
Types of chains that
can be sharpened
Weight
(complete machine)
(*) - the declared vibration total value and the declared noise
emission value have been measured in accordance with a
standard test method and may be used for comparing one tool
with another;
- the declared vibration total value and the declared noise
emission value may also be used in a preliminary assessment
of exposure.
WARNING:
- The vibration and noise emissions during actual use of the
power tool can differ from the declared values depending on
the ways in which the tool is used especially what kind of
workpiece is processed;
- Keep any stress caused by vibrations as low as possible.
A few hints to reduce stress induced by vibrations are: wear
gloves while using the appliance and work for short periods
of time. By doing this, consider every component of the work
cycle (for example, the moments when the appliance is
switched off and moments when even though it is switched
on, it is idling).

8. PART DESCRIPTION (FIG. 1)

1 Base unit
2 Arm unit
3 Vise unit
4 Chain blocking handle
5 Vise blocking knob
6 Chain jaws
7 Chain blocking unit adjustment knob
8 Chain blocking unit
9 Arm operating handle
10 Grinding wheel guard
11 Grinding wheel
12 Sharpening depth adjustment knob
13 Main ON/OFF switch
14 Electrical power supply cable
15 Rating nameplate
Sharp Master
120V~ 60Hz
85W
Outside Ø.105mm - InsideØ 22.2mm
Thickness: 3.2 mm
-1
7000 min
10 min
LpA=52,7dB(A) K=3dB(A)
LwA=65,7dB(A) K=3dB(A)
2
< 2,5 m/s
1/4" - .325" - 3/8" - .404"
1,6 Kg (15,2 N)
EN

9. SAFETY DEVICES

The grinder is equipped with the safety devices illustrated
hereafter:
- Grinding wheel guard: it protects the operator from parts
of the grinding wheel that may come away during the
sharpening process.
This guard must always be fitted in place when the machine
is in use.
Always make sure the guard is efficient and fitted properly
before you use the machine. Operator's safety could be
compromised if the guard is damaged and/or cracked.
- Switch: the machine is equipped with a temporary
operating switch: when it is released, it automatically
returns to the "open" position. This means that the machine
is always to be operated intentionally.

10. INTENDED USE

This machine is an electrical grinder for chains used in
chain saws.
- Use the machine exclusively for the types of chains stated
in the technical data chart.
- Do not use the machine to cut or grind anything other than
the chains envisaged.
- Firmly fasten the machine to the bench.
- The machine must not be used in corrosive or explosive
environments.
- Any other use is to be considered improper.
The manufacturer is not liable for damages following
improper or incorrect use of the machine.

11. UNPACKING

The grinder is supplied already partially assembled.

12. STANDARD SUPPLY (FIG. 2)

1 - Grinder
2 - Grinding wheel OutsideØ 105mm -
insideØ 22.2mm - th. 3.2mm
3 - Owner's manual
4 - Test card
5 - Screw 3.5mm x 9.5mm
6 - Grinding wheel guard
7 - Sharpening template

13. INSTALLATION

ATTENTION
Do not install the machine at eye level. You are recommended
to install it at a height of no more than 1.2-1.3 meters off
the floor.
The machine can be bench mounted.
13.1 BENCH MOUNTING (FIG. 3)
- Securing the base unit (fig. 3): use 2 M6 screws complete
with washers and nuts (material not supplied), inserted in
the securing holes F4. Make sure you position the base
unit on the bench as illustrated in the detail so that the
reference notches at the bottom touch the edge of the
bench.
9