Technical Data; Noise Information; Items Included - Bosch PBD 40 Notice Originale

20 | English
(33) Button for speed indicator/drill depth indicator
(34) Zero point button
(35) Set screw for adjusting the clamping force of the
brake
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Bench drill
Article number
Rated power input
No-load speed
– 1st gear
– 2nd gear
Laser type
Laser class
C
6
Divergence of laser line
Max. drilling diameter
– Steel
– Wood
Chuck capacity
Drill stroke max.
Total height
Base plate dimensions
(width x depth x height)
Weight according to EPTA-Pro-
cedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise information

Noise emission values determined according
to EN 62841-3-13.
Typically, the A-weighted sound pressure level of the power
tool is 73 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
1 609 92A 4N5 | (25.09.2020)
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
PBD 40
Avoid starting the power tool unintentionally. The
u
3 603 M07 0..
mains plug must not be connected to the power supply
W 710
during assembly or when carrying out any kind of
work on the power tool.
rpm 200−850

Items included

rpm 600−2500
Carefully remove all parts included in the delivery from their
nm 650
packaging.
mW < 1
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
2
– Drive unit (12) with drill column (4)
1
– Base plate (1)
mrad 0.5
– Quick-action clamp (3)
(full
angle)
– Parallel guide (19)
– Hex key (23)
Note: Check the power tool for possible damage.
mm 13
Before continuing to use the power tool, carefully check that
mm 40
all protective devices or slightly damaged parts are working
mm 1.5−13
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
mm 90
check whether any parts are damaged. All parts must be fit-
mm 650
ted correctly and all the conditions necessary to ensure
mm 330 x 350 x 30
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
kg 11.2
ised service centre.
/ II
Mounting individual components (see figure A)
Before initial commissioning, you must assemble the power
tool as follows:
– Slide the quick-action clamp (3) over the drill column (4).
– Insert the drill column (4) into the base plate (1) so that
the guide pin (25) is inserted into the guide groove (26).
– Tighten the fastening screw (24) using the hex key (23).
Mounting on a work surface (see figure B)
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
– Use a suitable screwed connection to secure the power
tool to the work surface. The holes (18) are used for this
purpose.
Bosch Power Tools